You are using an out of date browser. It may not display this or other websites correctly. You should upgrade or use an alternative browser.
board
Board International S.A. is a Business Intelligence (BI) and Corporate Performance Management (CPM) software vendor known for its Board tool kit. The company was based in Chiasso, Switzerland, where it was founded in 1994, and Boston, Massachusetts.Board International now operates in 19 countries, with around 3,000 customers from a number of variety of industries,
Hi,
I’d appreciate views on the fuse board.
https://ibb.co/xj0BtZt
It’s been completely rewired and I’m unhappy with the quality.
I’ve messaged him about it and described the board as a complete mess, and poor workmanship ship. For entry for the 25mm cables and 16mm tails he used the knock...
Anyone else had the same issue? Since this company keeps replacing machinery very often the MCB's get changed a lot so over time the slider contacts doesn't engage properly anymore.
Hi
Weird problem.
I’m replacing plug sockets. I isolate the circuit for the particular sockets at the fuse board so it is safe to swap out. All good. Suddenly the RCCB for all sockets - not just the circuit of the sockets I have isolated - trips. Why is this happening?
The RCCB doesn’t trip...
Hi, anyone know if a Schneider Easy9 Mainswitch & RCBO's will fit in a Acti9 board ? The Acti9 board in question is fitted in a single ph domestic dwelling and I want to swap out the existing mainswitch RCCB with a 100a switch which is Easy9 fare. Similarly will Easy9 RCBO's fit an Acti9 board ...
Hi this may be a simple answer to my question but I can't find the answer in the regs
If im fitting a garage board from a consumer unit with RCD protection do I need to have RCD protection in the garage board?
I'm guessing I don't need an RCD at the garage board but I can't find a definite...
Costumer have 12 flats and need to feed for each flat a prepaid meter and consumer unit within the flat , the main supply to building is three phase , my question is how to distribute the load for 12 flats, each flat have a load of 63A.
Main supply is three phase .
Hello engineers. I did EICR in two bed rented flat in a block of flats. There is old plastic fuseboard just above the entry door. There are only bs1361 fuses inside and no RCD. All luminaries are plastic.The board and wiring are in good condition. Any advise on how should i code that?
Hello, I've worked on a few old lewden boards recently and the quality is terrible. When fitting rcbos in 16th edition boards there's a solid bar that gets in the way of the taller device and they go in wonky enough as is. I was considering swapping it for a 100A flexible link, are any of you...
Evening all...
I need to fit an RCBO into a consumer unit, but I don't know if any were made.
I don't the name of the consumer unit, what it looks like, what age it is or which country it is located in. Could you let me know which RCBO will fit in it please @westward10 and send me a link asap...
A customer recently lost power to part of their electrical installation. On arrival I found all IEC 60947-3 devices had supposedly tripped - including the main switch rated at In 400A. Excluding the possibility of someone tapering with the board, can anyone think of any other reason why this...
Hello,
I’m about to take on a mains room for a block of flats and the DNO are giving us a supply of 259kva.
Now, would I need a 200amp TP-N isolator or a 400amp TP-N isolator from the main head to the ryefield board? I am also assuming I will require a CT chamber. This is my first project of...
I'm replacing my consumer unit (well, adding a second one, rewiring the house one circuit at a time, then removing the original one when it's all done) and looking at the FuseBox F2014MX 14 way main switch board with SPD. I intend to populate this with AFDD RCBOs.
The electrician...
Hi,
I have a low voltage landscaping transformer. The control board is bad so it cannot be turned on. I’d like to bypass the controller and connect the wires directly to the transformer itself (the toroidal). However, when I open it, in I see the white (neutral) and black (hot) wires input to...
Earth to Neutral 2 ohm with Multimeter on alighting cct. The cable disconnected from the switchboard.
I am new here and appreciate everyone looking at this post.
I come from an Industrial Electrical background and would like advice on fault finding.
My house has 1 lighting RCD. There seems to be...
Am I certified to sign off/do certs for a fuse board if I've completed my Level 2 and level 3 city and guilds (2365) electrical installation?
(have not done the regs yet or testing & inspection or the NVQ)
I am to install a car charger that states a type A RVD is to be installed. Can this be put in the garage from the non rcd side of the board or is it better to change the RCD on the board and use that side. I assume it makes no difference
Hi all, new to this thread and just looking for some views.
I have today attended a industrial unit which is being converted into small individual offices. An electrician has previously been here and has taken 3 individual sub mains from the existing three phase consumer unit to single consumer...
I need to fit a small sub-main board by my service head, to feed a garage unit in an outbuilding.
I am thinking of using a Chint shower unit (Screwfix), but replacing the internals with a S Type Time Delayed RCD.
Is this a valid approach for a sub-main, as opposed to using a switch/fuse unit...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.