Just looking for resources, books and videos ideally, that show how to actually do the physical job. ie you need to wire some lights in, what's the best method to bring the feed in to the lights, or you need to put sockets in, what's the most efficient way to do the job ie chase out first, put...
I have a 20mm steel conduit drop to an accessory box buried in the wall. It was previously used for lighting cables and had 2 x 1.5 t+e and 1 x 1.5 3+e squeezed into it. There is no actual conduit system installed - the conduit simply goes into the loft and ends. There is some kind of rubber...
I'm just a DYI-er here and very new. I have an ungrounded outlet that is completely controlled (it's not half-controlled) by a wall switch. The place I'm in was built in 1957 and this outlet appears to have a jumper wire from neutral to ground. Notice in the attached pics that there are 3...
Hi everyone,
I want to install a wifi switch in my room but the problem is I am not very informed in electrical wiring subject so would appreciate it if someone could give me some insight regarding this.
Light Switch Cables Image
The in the inside it says TOP 7704
There is nothing saying which...
Had a nightmare of a day trying to get a small 2 bed 1900 or so terrace house through its EICR today for the landlord.
He's one I work for, so its a case of fix as I go to get a satisfactory rather than just report.
2-3 hours was sorting out the downstairs lighting circuit failing on IR L-E...
Anyone used them wagobox capsules for swa Cables?
I’ve got an external lighting job with semi hidden joints wanted and the capsule top flush with the grass.
Good morning,
to carry out IR testing for armoured power cables in man panels ( pls see below image), do you remove the cable from circuit breakers on both ends or we can test them as it is?( by putting the probes on the cable lug or circuit breaker screw, depends the type of connection)
Hi,
I have a cluster pendant light with 6 cables hanging down and a small LED light at the bottom of each. I need to replace one or two of the cables to make them longer, does the cable have to match the spec of the others? i.e. if 0.5mm² has been used can I use 0.96mm² for the replacements or...
evening all
I am wondering what the installation methods should be for cables run under floor boards and then into stud walls but without thermal insulation...102,103 dont seem relevant and so my understanding leads me to think it would be a cross between c for clipped direct under the boards...
Hi. I'm a newbie here and want to make my own computer cables. Most computer cables are sleeved paracord, mesh or silicon but I want to make more rigid cables that are able to bend somewhat easily. I stumbled upon the pictures attached and they look like some metal jacket sleeves. Does anyone...
Doing a commercial EICR, the original electrical is very good, 25 years old, all trunking and conduits, with klicks on tube near as dam it above the light. (This is what I was brought up on) Anyway cat5 or whatever have been lashed across the ceiling no support or anything. Is this now deemed a...
Are DNO cables in the UK fused before going into a building? And if so how? What happens if you were to short the cable out before the cutout main fuse?
View: https://youtu.be/HQSohl-C_nk?t=180
Had to do a CU change in this lovely heat, so naturally it was a bit of a bugger...
Replacing a Wylex skeleton board with Type 2 breakers for a Wylex skeleton board, as client wanted it to remain hidden.
The previous board "enclosure" was made up of the nasty brown plastic front (always...
Currently my builder is placing the cables straight under the slabs between the hard-core and cement. Should he be doing this or do they need to be insulated?
Hi All, opinions please, just been to a property that has a 6mm cable ontop of 200mm of loft insulation so not buried. What de-rating factor would everyone apply to this
Would it help if i could get it in some big trunking?
Hello
I need to extend 13 5 core 6mm non swa cables, the joint's will be outside - above ground with no weather or sun protection.
Any advice on the best product to use for this task would be appreciated.
Thanks
Chris
Due to a change of inverter location I need to lengthen some 4mm dc cables. These are run in plastic flexi conduit. No space for adding mc4 connectors and a junction box or dc switch would be difficult. Is it acceptable to crimp a butt joint and double heat-wrap over the joints? Each one will be...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.