Can anyone recommend any good UV protected conduit for runnign network cable externally?
I plan on running around 10 cables (7mm diameter each) from the loft to the 2nd floor and ground floor, but the cables are orange and i'd like to hide them in some pvc black conduit. A lot of the stuff i've...
Any recommendations? I have 25mm steel conduit going into 20mm reducers feeding a plastic time guard switch and then returning to steel conduit again on the other side. An earthing nut is too chunky. I think I need those smaller flat brass plates you get on SWA cables.
1588093418
Found them -...
Hi guys,
Bored at home, so making a bench using old conduit I ripped out. Trying to use as much recycled as possible and was wondering if anyone had anything lying about. Looking for 8 x dome covers and 8 x tee’s, inspection or solid. All 25mm. Will pay postage ofc.
cheers
I need to run a length of steel conduit. One end it will connect into a standard 25mm BESA box, on the other end, it will go into a sharp elbow. The conduit has to thread through a hole in the floor that is very close to the wall. If I thread the conduit through the hole and then place either...
I’m looking to buy some PVC Conduit for some security lights rather than clip the cable. We don’t use it in work. But I know I need 20mm conduit but would I be okay using 20mm inspection elbows? I assume they just fit inside?
Hi,
Which do you guys use? I've bought the light stuff as it's going in a shed where there's not going to be any risk of mechanical impacts. It seems unnecessary to spend extra on the heavy stuff.
Is the choice to use heavy gauge purely due to its greater mechanical protection and because...
Hi,
Im putting my girlfriends tumble dryer in the garage. The wiring will be in black pvc conduit, i would like the conduit to run approximately 6-12 inches horizontally above the dryer to a double gang socket to plug it into.
My concern is the mutual detrimental influences of the dryer...
What kind of wire conduit would you use with a generator inlet? Specifically the reliance controls pb30? Im trying to run it from an inlet port to an outlet port. The four wire Romex or whatever is litterally connected to a 240v l14-30 outlet inside my apartment. So I wanted to put that box on...
Good afternoon one and all
Does anyone in the Dorset area have good experience with steel conduit? If so please could
I pick your brains on a few things?
Looking for some pointers in the right direction if possible. I come from a background of domestic work and general house bashing but I’ve been given the chance to expand my work into more commercial stuff. I will be doing this under guidance from a good friend of mine who is more commercial...
Background
I'm running some low voltage cable (e.g. CAT6A data cable; coax cable; HDMI cable and speaker cable) to a number of rooms of the house and would like advice on the best way to do this to avoid plastering the cables into the walls - to give me flexibility to remove / pull new cables...
Hello,
I'm looking to improve my cut time and quality using a better tool other than a traditional hacksaw.
I've been looking around and all I could find that looks like it can do the job of cutting pvc and galvanized steel is this: Milwaukee C12PC-201C 12V 2.0Ah Li-Ion RedLithium Cordless...
Hi , I nearly done my assignment, but I need help for couple questions, Please I wanna make right everything.
I still think with conduit, better used for main workshops, and I need drawings how to join in DB.
Can you help me please or just asking someone.
Good evening Gents
Om after some help and advice please on setting up a new conduit bender.
Im wanting to ask how to score a mark on the forming wheel to indicate bending points etc?
I usually do the way of doing a bend then offering up and trimming excess off but would like to learn the old...
Good day, can i connect a pvc cord grip to a pvc conduit or pvc flexible conduit? The cord grip is also connected in a pvc junction box. Thanks everyone
So i have a client who wants a room down with surface conduit, industrial look. No problems there, i am a little worried about the material tho. I feel the galv coating on some of the saddles and pipework isn't great these days. its fine for a workshop but when its going to be a feature like...
Hello!
My electrical utility has decided to take our power away - occasionally - to prevent fires. So I have ordered a modest backup generator. To conveniently power the house without running extension cords everywhere, I need a transfer switch.
I have tentatively identified the...
Eh up :)
As per the title, "Is galv conduit containing insulated and sheathed cables (e.g. T&E) still an exposed-conductive part?"
Clearly, if it contained unsheathed singles, it obviously is.
If it's not an exposed-conductive part (and it's not extraneous in the case I'm thinking of) then it...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.