copper

Recent contents Top users
  1. HappyHippyDad

    Is this tinned copper and is it classed as copper with regards scrap metal?

    I am having a cable stripping day in the garden whilst the rain clouds have gone. A few cables from older houses look like they are tinned copper. Here is a picture of the tinned copper and normal copper. Is it tinned copper? It was taken from imperial cable. Also, will the scrap yard treat...
  2. C

    Discolored Copper

    Does anyone know what causes this? Is the wire safe to use? Does it have the same conductivity and anneal as "regular" copper? For that matter does this occur with UK rolls of twin and earth?
  3. J

    UK Insulating copper tube splices

    Hi, what are people using to re insulate a copper through crimp In a metal adaptable box please? Also my SWA CT650H crimp tools don't want to crimp splices - E.g On the 10mm setting a good tug and the splice falls off, setting to 6mm will crimp nice and snug. But thats not great. Any guidance...
  4. D

    Coax Cable Insulation Damaged, Copper visible, Cable can't be easily replaced I think

    Hi, I'd really appreciate your help. This is in Europe. I have no electrical knowledge and very little construction/DIY knowledge. I know electricians / cable-provider-technicians can measure coax signal strength at the outlet with a specialized device. A cable is damaged right down by the...
    • Delran
    • Thread
    • cable can't coax copper damaged floorboards insulation replace replaced wall
    • Replies: 6
    • Forum: UK Electrical Forum
  5. HappyHippyDad

    Which parts of a consumer unit are copper?

    I am getting into the habit of stripping fuse boxes and consumer units when I replace them. However I was wondering which parts of the CU are copper. Neutral and earth bars? The screws in the neutral and earth bars? The bit that the old BS3036 fuses push into? I enjoy pottering for a few...
  6. O

    EICR and non standard conductors

    Hi Guys, Just wondering what I write on an EICR when I come across different conductors, I have a job with what I think looks like multi-stranded 4mm tinned copper on a ring. Particularly in the schedule of test results, do I just say it's 4mm/2.5mm and then add it as an observation, is it even...
  7. driverman

    CCTV > Router Cat 5/6 solid copper cores

    Hi Guys, I have asked this question before in another thread that I was following, but can't find it. I've installed a CCTV system. What I'm after is a 10m x suitable Cat 5 or 6 cable complete with plug ends fitted. I believe it was suggested that copper solid 8 core cables are better. The cable...
  8. Marcus Vaughan

    How Old is Copper Clad Aluminium etc

    Hi All, I'm part way through testing an empty old house with all sorts of older wiring and a 3036 board in order to work out whats needed. First circuit is copper clad aluminium ring final. I measured one of the strands and have it as 7/036. Question - am I wrong to assume is imperial? I do...
  9. C

    Should we use copper blade crimps?

    hello guys I quite often find that when terminating 25mm tails into a 100a fuse board isolator you do not get the 25mm tails to squash nicely by the main switch thermals like you would 16mm tails, should be be using copper blade terminals instead to ensure a better connection?
  10. AlmondSauce

    Bonding outside copper pipe

    We have a copper pipe running along a wall outside in the garden - it's used to supply a sprinkler system. (Inside the house it's plastic, there's a join to copper just before it comes outside.) Should it be bonded? It's not at present. All my knowledge of bonding comes from pipework running...
  11. diyterry

    Earthing copper pipes .............

    While ripping the old bathroom fittings out I noticed that none of the pipework or fittings were earthed. Should they be earthed and if so what is the preferred method?
  12. D

    Cable plasticiser reacting with copper.

    Firstly no Ghostbusters jokes!! Was called out to a job yesterday where a light fitting had been 'buzzing', upon inspecting it I saw the terminals and cable were covered with a 'green slime'. After a quick Google I found out this is quite common and that it the plasticiser of the cable reacting...
  13. D

    copper equivalent of steel

    Does anyone have the copper equivalent of a two core 16mm SWA to hand? Or the minimum SWA 2 core CSA in which the steel would be equivalent to a 10mm copper conductor? Don't have the info to hand. Thanks.....
    • Deleted member 9648
    • Thread
    • copper equivalent steel
    • Replies: 9
    • Forum: UK Electrical Forum
  14. J

    Earthing Copper Pipe Lamps Query

    Hi, I build lamps from copper piping and various other bits and bobs (including the occasional trumpet!!). The lamps are made from sections of copper pipe connected to elbow joints and other copper plumbing connectors. The lamp terminates at a brass lampholder at one end and a plastic clamp at...
  15. BeardyJaws

    EP Bonding Copper pvc copper

    Hi, a little clarity required please. I’ve recently been to a property to make an emergency repair to a broken cable ( they drilled through it). I’ve patched the cable for the moment but while I was looking at the bonding I found the CH pipes bonded next to the incomer but not the incomer...
  16. marconi

    ELECTRONS IN A COPPER WIRE - SPEEDY OR SLOW?

    EF readers may be interested in learning more about the electrons they skilfuly control on a daily basis. See: Copper and electricity. Drift velocity. - http://resources.schoolscience.co.uk/CDA/16plus/copelech2pg3.html
  17. J

    copper conduit possible or not

    Hi I am doing a job where the client wants some sockets wired in copper conduit for surfaced mounted sockets on a exposed concrete wall.... has anyone ideas- or steer them towards just using galv!
  18. andysparkfree

    95mm 4core SWA, just trying to go definitive on the steel to copper calculation

    good afternoon guys I have a 95mm 4 core swa to this new office build , thats fed via a new exterior mains panel located next to a new sub station. now all feed cables on this project have been designed by an independent company, and i currently have flagged up that i believe that using just...
  19. S

    Tinned Copper cables ccc

    Evening, has anyone got the current carrying capacity for old Tinned copper cables. Im looking at using an existing cable that looks just under 6mm (Imperial size most likely) for a cooker circuit. IR etc tests out ok. Thanks in advance.....
  20. E

    Copper Pipe Lamp Earthing

    Hi all, Hopefully someone can help me. I am going to undertake a small project for my home which will be a copper pipe lamp for the living room. I bought a lampholder and wire and have a few questions before I start. The lamp holder is metal with a ceramic insert (see pictures). I have also...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

Tags

advice aus cable circuit course earth electric electrical electrician hello led light lighting lights looking new please question rcd socket supply switch testing training wiring
This website was designed, optimised and is hosted by Untold Media. Operating under the name Untold Media since 2001.
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock