Hi Guys,
I'm doing my Level 3 C&G design project and just have a few design related queries which i am so far struggling to find clarity on either in the text books/guides or online.
- Main issue is circuit lengths for lighting for calculation volt drop and ZS:
With power its seemingly quite...
Was out at my mechanic today
Hes.got this huge open area to the front of the garage
Access to the garage is by a side entrance and round the back. A lot of manouvering and assistance required at times to get in and out .Go figure.
I've been caught out so many times by rushing into jobs...
Hi all,
This is my first time posting something on this forum. I'm busy putting together a design for some LED lights that are going to be mounted on some columns along a pathway. The supply will run twenty odd metres to an enclosure on the outside of the building that will encase the...
HI Folks.
This is my first post so apologies if it's in the wrong location.
I recently installed a 3kw Solar system with an iboost diverter which diverts electrical power to the dual elements (3kw and 2kw) on the water cylinder when there is an excess of power.
I recently discovered that a...
Good morning I wonder if I could have some confirmation in regards to a radial circuit.
I have been showing apprentices different methods if wiring ring and radial circuits.
I wish to continue this next week.
I can not see any regulation not permitting the drawing enclosed, I would just like...
They can double as a heat gun at the back while you're frying your chips
Now I appreciate they will have a warning in the manual probably to keep them 300 away from anything but most people won't take any notice
Hi everyone
So I'm just starting my 2365 design project relating to a hotel extension and pool/cafe area, has anyone recently completed this assignment? Any advice would be great!
A little protip for my fellow students/trainees; When you get your design project and the absolutely gorgeous (no really) A3 drawings for the project(s) - DO NOT DRAW ON THE A3 ORIGINAL.
Think about it, you have anywhere from 5-10+ circuits to draw in, each with its own path, possibly sharing...
Passed my C&G 2396: Electrical design and verification course recently and loved every minute of it, however I am wondering if it was actually worth doing. I haven’t seen any adverts with it listed as a requirement or even as preferred. It’s a level 4 course so a bit surprising. Has anyone done...
Passed my C&G 2396: Electrical design and verification course recently and loved every minute of it, however I am wondering if it was actually worth doing. I haven’t seen any adverts with it listed as a requirement or even as preferred. It’s a level 4 course so a bit surprising. Has anyone done...
Hi there. I'm building a house and need some help with the LED lighting design. Lots of experience wiring things, some experience using LEDs (did a run of low voltage landscape lights at previous house.) But first time with an LED lighting design this extensive.
This house has a very open...
Hi guys I’m studying from home for level 3 and it’s very hard. Could someone please help me pick which wiring system I should use in the main workshop for the luminairee- and why that system would be best. I have attached the pictures of the information you may need below.
Hi Everyone,
I am currently an Electrician and have been for 10 years now. Going to cut straight to the point...
I am wanting to look down the route of becoming an Electrical Design Engineer. I am aware of the City & Guilds 2396 Course but I am not naïve enough to know that once I get this...
Hi all
I'm doing a kitchen rewire and in kitchen client has also had a new water cylinder installed. It is a Main unvented direct 170L. I have been trying to get through to customer support but is non existent. I have not wired many new circuits for water heaters and am a bit confused with the...
Good morning and a very happy lockdown to all :)
I'm using this tedious 'holiday' to fit a new suspended grid ceiling in my large open workshop.
Here's the provisional lighting plan, using drop-in 600 square LED panels from TLC. I have three existing circuits available (currently feeding 5 x...
In Short: I need help designing a circuit between a receiving induction coil and a battery load.
Longer Explanation:
I am entering a science fair project this year which requires wireless charging of a drone. So far, a have a transmitting coil that takes 12V at 2 amperes and the receiver coil...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.