Not specific to industry. But in a factory I sometime do work for, they have a line that is 300m long and they want welding sockets 32amp 5pin along the length of it. Ok. The cable they have bought for the job is 6mm 5 core. I politely declined the job and suggested calculating the size of...
So I built a 15ftx5 enclosure for my chickens and ducks. They seem happy and I'm generally happy with it. However, it has 1 problem with the design and I need some help.
Everytime we get a day or 2 of rain it literally fills up with water. I believe most of it comes from rain blowing into the...
Hi all I am having trouble trying to work out the total load and swa cable size.
I have 10 circuits in a outhouse 40 meters from the mains power supply 1 x lighting with 10 lights, 1 x lighting with 10 lights.
1 x 2.5mm radial for 2 heaters, 1 x 2.5mm radial for heater. 3 x 2.5mm socket rings...
Iv got a little install of 2 IP rated sockets to go on an exterior wall of a log cabin. The customer doesn't want to see any cables or containment as you look at the sockets. We've agreed to run black PVC conduit on the rear of the cabin (which is going to have shrubs growing up it) and then...
Hello I’m 25 year old electrician.
Nvq qualified 18th edition and 2394/5.
I enjoyed studying and bettering myself but now I’ve gone stuck and looking for opportunities I don’t see myself as a manager.
I’m thinking of a specialism or a electricial designer I’ve googled this but can’t seem to find...
Hello I’m 25 year old electrician.
Nvq qualified 18th edition and 2394/5.
I enjoyed studying and bettering myself but now I’ve gone stuck and looking for opportunities I don’t see myself as a manager.
I’m thinking of a specialism or a electricial designer I’ve googled this but can’t seem to find...
Hello, This is my very first thread on the forum. If I posted it in wrong part of the forum, just moved it. Thanks.
According to the thread ( FREE Electrical Software from the Copper Development Association -...
Evening,
I´m looking for some Electrical Design Software for designing electrical cabinets. So the software would need to have contactors, drives, PLC´s, isolaters, SSR, solenoids etc.
I´ve used Design Spark Electrical before but I found it difficult and cumbersome to work with, so for that...
Hi all, im new the the forum.
Curently doing the city and guilds 2365 level 3 course. Got a question regarding the 305 design assignment.
When filling out the table to calculate the voltage drop and calbles sizes, do i use the design current etc before or after the diversity factor?
Hello,
I am just starting my project. I have uploaded the questions.
Questions 2B & C
Socket for the kettle - each of the tables.
Socket for TV - next to the Kettle, as I assume it's not wall mounted.
Two single sockets for Laptop/phone to each side of the bed
FCU - by the main entrance...
Hello :)
I'm currently on my final assessment for 2365 after spending two years at college.
I really want to complete the assessment in some design software rather than manually drawing.
I found designspark which looked as if it could do what I want but doesn't seem to like importing...
Hi all, new to here.
Just designing a sub main, very long time since I have done this so just wanted some thoughts. Its to a summerhouse sort of set up that will be at the bottom of a very long garden at a later date (sockets, lighting and hot tub planned from the board). Patio is getting done...
Hi, hope everyone is enjoying Easter!
I have boon looking for an induction hob recently and found one on ebay for £25 and close by so I bought it, yay!. It was purchased as defective, its a 5 sone hob and the two left zones did not power up. A bit of research before purchase shows there were...
Hi this is the electric car charger, is this suitable? Can anyone point out anything I've missed. Also what is the best way to draw the circuits onto each drawing. Any suggestions are great fully appreciated
I’ve recently started my level 3 course and I’m doing electrical system designs the one with the hotel extension and pool and café block but I stuck on all of question some guidance would be appreciated thanks
Can anyone tell me what this symbol represents? I'm assuming it's something to do with a wall light, possibly something to do with a vanity section as its in a changing room but I can't find the symbol anywhere. Cheers!
Hi guys,
I'm recently qualified so naturally a bit hesitant on my first jobs so looking for advice as much as possible.
I'm working as a junior at a domestic job where the customer has a large garage which has a sub main (run from the main unit in the house via SWA) consumer unit in it...
hi all,
Can anyone provide a worked example of rating a breaker for a circuit.
For example
In an industrial environment, we have our own HV supply and each substation on site has its own earth rod. I assume this falls in to a TT system.
if I wired (14) 8watt lights in parallel back to a...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.