enclosure

  1. M

    Enclosure For Rcd To Protect A Tt System, Have I Got This Right?

    Having a hard time figuring this one out, think I've got it but I figure best check with you guys! On a TT system, metal CU so needs to be protected by a time-delayed RCD in the tails (to allow smaller Amp RCDs on sections of the board to trip first), and this time-delayed RCD should be in it's...
  2. kingeri

    CU enclosure replacement: repair?

    Customer has cracked the corner of his CU, with a little effort you can get your finger through the crack. I am going to swap the plastic CU chassis, but not in any way alter any of the circuits. I am thinking this is a repair, and hence not notifiable, any thoughts? Also, beyond checking the...
  3. Soulsurfer

    Mains move possibly ?

    Hey all, just been to see a client ref possible full rewire ( she would prefer just odd cabling changed i.e. odd ring legs etc... ) and during she mentioned where service comes in the property just in lobby/hallway into usual cupboard kind of affair. Basically she has a staircase like almost...
  4. HappyHippyDad

    Which unit/enclosure to house upfront RCD?

    Evening.. Just looking at a CU change on a TT. I'd like to put a 100mA S type RCD before the CU. Is a 2 way (4 spaces) amd 3 metal board my only option? Its a bit big!
  5. F

    Cutting Slots In In Metal Dist Boards

    hi lads what ru using to cut slots in metal dist boards consumer unit my old jigsaw has justgiven up on me many thanks paul
  6. G

    Earthing inside a submain panel from main swa incomer

    OK, going to keep this short. Supply is 150mm 4 core SWA, with NO supplymentary earth ( calcs done by others, ) QUESTION IS. Do you NEED to run an earth ( is it a regulation) from banjo on inside to earthing terminal inside board. Common sense and a simple ohms continuity test (0.01 ohms)...
  7. E

    Metal enclosure for DP Isolator

    Hi Due to the location of the meter on an upcoming job I am installing a new consumer unit in a space where there will be a full height kitchen cupboard and am exploring ways to run the meter tails up (from about 1m directly beneath in the bottom of the cupboard) to the CU (ideally the client...
  8. E

    Heating system wiring

    Im just in the process of installing a large heating / hot water system in a restaurant / bar and need some advice on selection of gear for wiring it. I would really like to have everything going back to a main "din rail" enclosure. I need to install relays in the system as I have 6 motorised...
  9. S

    Mysterious temporary earth fault in 3 phase motor starter enclosure

    During the time of phase absence measurement temporary earth fault was detected on the enclosure of 3 phase motor starter. I assume earth fault loop impedance testing was performed in recent history but somehow it failed to protect from consequences. Due to dodgy British standards and...
  10. D

    Enclosure for 2 Relay Switches

    I have 2 relay switches to control switching between my Air Source Heat Pump and my Oil fired boiler. I want to mount them on rail within an enclosure similar to a Consumer unit housing. I am struggling to find a neat solution. Any ideas?
  11. D

    Non-Harmonized cable in Enclosure

    Hi All I am currently designing a complete home automation system based around CBUS dimmers and relays. I have now built the enclosures with the dimmers and relays in so I can start programming / testing them. I have going to get a full spark to install the actual cables and connect the lights...
  12. Spoon

    Pneumatics and electrics in the same enclosure

    Hi Everyone. One of my work guys has asked if its ok to put pneumatics in an electrical enclosure. I don't think it is, cause just in case of a fire, and I think I have read it somewhere in one of the regs books that you can't. I have done a search for Pneumatics on this forum and looked in...
  13. HappyHippyDad

    IP 55 Enclosure from screwfix! code 33991

    I have just used 11 of these boxes with SWA terminations They are awful and I dont want someone else to have the same problems I did. They seem ok, quite sturdy and the price attracts you, however one or two of the screws snapped when doing up the front cover and then MANY more snapped when...
  14. uksparks

    Din Rail Enclosure

    Hi, Does anyone know where I can get a Din Rail Enclosure like this, well this size, Dimensions (w x h x d) 300mm x 220mm x 120mm Basically the Wago DRE-5 DIN Rail Enclosure, which It wont let me link to. For less money? The other thought I had was to use an empty MK consumer unit to put...
  15. Paul.M

    Car catches fire in Lion enclosure!!!

    Not the best position to be in, lucky family. Car Fire In Lion Enclosure: Family's Terror
  16. jibjob

    Boiler in bathroom EICR code

    Hi Guys, Came across this today in what seems like a newly refurbished bathroom. As you can see from the picture (hopefully) is that the boiler is less than 600mm from the edge of the shower enclosure. Not sure what the IP rating of the boiler is but the adjacent switched connection unit &...
  17. G

    Eicr Code

    6mm singles from 100a TP 60947-2 in a main panel to an adcent enclosure to a 16a 60898-D Tp, then 6mm leaving this to air con units. Would you code 2 the 6mm singles from the 100a 60947-2? As exceeds current carrying capacity?. Or because the 6mm singles are less than 3 metres to the enclosure...
  18. S

    3 Phase in a small house! lol

    My handy work connecting 3 consumer units in a house full of storage heaters! lol First for me seeing 3 phase in a domestic house.
  19. R

    some nice work

    Hi just thought i would show you guys some photos of the work iam trying to replace.Photo 1 is 4core 35sq mains feed to 2 storey office block, no2 is i.5 feeding lighting in several offices this is the best photo of the circuit the rest contain old rubber,single pvc only surface,conectors...
  20. L

    Odd Shaped Metal Enclosure

    Hi All I am after a metal enclosure within the following measurements if anyone can help me out: between 60*60*220mm and 100*75*300mm (W*D*L) If anyone can help it would be greatly appreciated (Im after 7 of them!)

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
This website was designed, optimised and is hosted by Untold Media. Operating under the name Untold Media since 2001.
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock