explain

  1. M

    Can someone explain how these storage heaters were wired via the contactor?

    Been round to a house to quote to replace some storage heaters for new panel heaters and came across a strange (to me at least) way of wiring the old storage heaters via a contactor in the board, as usually I see their own off peak consumer unit which powers up at night via economy 7. From the...
  2. K

    USA Can you explain to breaker info to me?

    I am buying a house and it was built in 1949. Is there anyway I can tell if it has tube wiring without opening up the walls? Is there anything else I need to watch out for with a home built in 1949? Also can anyone explain these 2 photos to me? Does any of it explain if there is tube wiring?
  3. B

    Can anyone explain the situation pictured to me?

    Was going through and trying get my breaker box all sorted came across this situation. Never saw anything like this.
  4. O

    Can anyone explain type A RCD's

    I get how they work and can kind of understand the reasoning, I remember the early "no-trip" RCD testers, D-LOG made one that saturated the RCD core with DC to stop it tripping whilst doing an earth loop test so I agree that stray DC leakeage could stop an RCD tripping. But, lets say you...
  5. J

    Can anyone explain this

    Mains supply into house is single not looped. However supply is spilt at mains fuse two 60A fuse one goes to the meter then on to the consumer unit, the other one goes into the wall completely separate from all the electrics in the house. Where is it going? And why not into a meter?. Old but it...
  6. J

    Can anyone explain how load management is installed?

    Hi, I've recently come across properties with high loads exceeding max demand, especially hmos I've heard about load curtailment and relays where when one heavy load is used another cannot be used. Can anyone provide information about devices used and how to wire them.
  7. BiddeldyBwah

    Can anyone explain how Klik's work?

    I'm working with these at work at the minute and they really confuse me. Unfortunately everyone is too busy to take the time to explain them properly so i'm left guessing. We have a 4 core YY coming from the board (which i've not seen), feeding a row of lights that is a mixture of emergency and...
  8. E

    Neutral went bang - can someone explain this wiring to me?

    I was wiring up an IP65 5ft LED batten today, straight swap for a non-LED version. The light was an emergency and worked off a sensor, no switch. The emergency was wired through the test switch. In the light fitting, there were 4 wires - brown switch live, black live, neutral and earth. As i...
  9. A

    Please Explain Double Insulation

    Hi, Just purchased a new wall light and it has no earth on terminal junction. Instructions say ‘double insulated - no earth required’. Here is a picture: How would this protect you if the wire from wall broke loose from this junction box and touched the casing which is metal? Or is it...
  10. S

    Just short explain of wiring

    Hello, Can anyone quick explain me this? Here in attachment there are screens of big motor where double power wires were use from frequency drive to motor terminal , i just want to know why it because bigger amperage needed to flow ? And if this same motor were used for star - delta switch by...
  11. C

    Please explain this transformer from a scientific instrument

    First post, DIY. I harvested this heavy transformer from an instrument that we took out of commission. I live in a 220v country and I want to know if I can use this safely to run 120v tools (like routers etc). 1. It states 2kv. Is this ~2000 or ~4000 watts? (i.e. do I multiply by 120 or...
  12. K

    Could I ask if you could help explain the comments re a Domestic ElCR report that has come back unsatisfactory please

    Background: I have a ex council 1st floor flat that I bought, I moved in to care for my disabled mum and so rented the flat as I could not do enough hours work and care. I was told I am a kind landlord and when asked to do things I will jump immediately as I would not like my tenant to have a...
  13. P

    Help, I’m sure someone can answer this very quickly

    Sorry, I’m new to this. Can someone just explain how I should wire these cables in the ceiling light unit as per images, there seems to be a lot of cables,
  14. D

    Can anyone explain this reading (suspected open circuit)

    Alright troops ! First post here ! Any one come over this situation before ! Yesterday i connected an existing feed for cooker good into socket but it wasn’t working when I turned on! I tested between live and earth (240v) between live and neutral (12v ) and neutral and earth (0 volt ) I...
  15. Q

    Can anyone explain why this would occur

    Good evening all I'm training to become and electrician and last week I came across an issue when we were attending to some outside lights. Basically the scenario was there was two outside lights:one was a small upright bulkhead fitting with an inbuilt photocell and pir this brought itself and...
  16. D

    Ikea Cooker and Hob Explain please.

    Hi, So i have turned up to a job and this information is all i have on how to fit a cooker and a hob. Am i right in saying these to can be connected to a 6mm wire with a 45a switch for the hob and a 16a switch for the cooker? Thanks
  17. sham

    Can somebody explain this.

    I copied this pick from another thread, nobody can work out why this is done. So I thought I give it a go here.
  18. S

    Can anyone explain this - strange wiring?

    Please can someone help to explain this IMG 20180717 204316 - https://ibb.co/i9RBKJ There seems to be 3 lots of live/neutral/earth. I saw this when I removed the old chandelier. Problem is, it seems that the three neutrals were not connected to anything and of the three lives, 2 were...
  19. 1capybara

    Can anyone pls explain 431.1.1 current cant exceed 145% of the smallest wire on the circuit?

    This can have several interpretations. 1. Break trip rating cant be above 145% of the ampacity rating of the wire? That doesnt make sense because the breaker should be protecting the wire by tripping first. 2. Load cant exceed 145% the ampacity rating of the wire? Load should be less than the...
  20. W

    part p can someone explain

    So im hearing all different versions from people. some people are saying that you need to pass a part p exam and become a part p electrician. Ive also heard that thers no such thing that its only a paragraph in the building regs and that anyone can pay a building control for a higher fee or if...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
This website was designed, optimised and is hosted by Untold Media. Operating under the name Untold Media since 2001.
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock