Good evening all,
Looking for a bit of a help, seems a relatively small task (hopefully). My property has a dimmer switch which no longer works, I purchased a replacement today although I'm now not certain that I will be able to use this as the connections are labelled differently from the...
Chaps and Ladies. New to this forum but thought I’d pass on some info having used the forum myself in the past as a lurker.
Been to a job today, not a job really but a mate. Oil boiler not firing. No lockout or anything.
Bit of background I changed the solenoid coil and control box back in...
My NIBE F2015 air source heat pump which is only 7 years old has an apparent fan motor failure. The fan turns freely and the motor starter capacitor has been replaced but the unit will still not run. Any suggestions for a fix?
A client currently has a wall switch in the bathroom which is no longer operating, the switch operates on the detection of heat from your hand.
to get around the regulation for wall switches in bathroom they installed a SELV switch which currently sits behind the tilling, you operate the lights...
I had an extension fitted and a single circuit added for the light. However, the light will only operate from the MCB and not the switch. As soon as I introduce the switch into the circuit and operate it from there it trips the MCB and will not stay on. Any thoughts on what might be causing this?
Recently i've fitted 3 outside lights with PIR, next to customers front door and one on my own garage, the £30 to £45 ones from screwfix...they last between a week and 6 months then go faulty... so i have to keep going back... any ideas..
So had to fit a new shower as old one kept tripping the rcd after few seconds assumed the shower was to fault as made a buzzing noise and tripped, on fitting the new shower it had same faukt so checked pressure of water no issue then checked wiring at box also no issue so moved onto next...
Heyy so I just turned my electric cooker on and it made a hugee bang and tripped the electricity in my entire flat ..
I flipped the switch and restored my electricity, but is it safe to try and turn my cooker back on?
Thanks!
I am planning to move a socket outlet. The CU is largely unlabelled so don't know which 32 MCB to switch off. There are 2 x 32a MCB. All other mcbs are for lights (6a) and a dedicated immersion (16a).
To isolate the circuit, I tried switching off the first of the two 32a mcb which isolated some...
Here's a typical scenario. Not sure what I should be doing or what I'm doing wrong.
Lets say your installing 10 battens with tubelights for a customer. You do the job and customer wants you to supply all parts including the battens and tubes.
You go and buy the lights from your supplier...
Hi Everyone
Has anyone had any problems with 600x600 panels.
I fitted some for a client and after a couple of days they have started tripping the MCB.They are on the same circuit but 2 switches and sometimes they seem to be fine but at times they would trip the Mcb.
I have tried to isolate the...
Hi all, I was wondering if anyone could shed any light onto this problem. Whilst doing subby work on a bathroom install, the owner of the house asked me to have a quick look at her kitchen lights. There was a 4 lamp spotlight bar type fittings. Apparently shes changed the LED GU10's about 3...
Before I start, I know this is not usual but I want to know if it's against regs.
I'm testing a conservatory ring, feed from a fused spur. There's a Live-Neutral IR fault between two of the three sockets.
The cable is embedded in the conservatory bare block wall.
If I just disconnect the faulty...
Never really touched on motors always been domestic, any ways il cut to the chase, got a job dol starter 3ph not stopping on em stop button, am I right in assuming it can only be the dol stater is nakered, and just replace it, or could it be deeper and be overload setting wrong etc etc. Also to...
Hi all,
I've just moved into a rental house and am having a nightmare figuring out what type of light bulb to use in the ceiling fixture in one of the upstairs rooms.
The bulb that's in the fixture now works, although does not dim (if I turn the dial at the wall). It also happens to be a very...
CorpusCallosum
Thread
dimmer
dimmer switch
faulty
fixture
light
problem
switch
ERBAUER ERT576SDS 2.8KG 36V 2.0AH LI-ION SDS PLUS CORDLESS DRILL
Excellent drill with great reviews on screwfix, never been used or out of box, with all original packaging.
Fast charger, 2 x 36v 2.0Ah batteries, depth stop
looking for £235
Postage £10
Hi,
I installed a security light 8mths ago, customer has informed me the light is only partially working.
Customer wants a replacement or upgrade and he will pay cost of upgraded fitting.
Where do I stand with this regards it being a manufactures Defect and not a fault of my installation...
Hi guys, first post on here.
I've recently fitted 4 new high frequency control gears into 4 old fittings. I've removed all the old gear out of the fitting with the exception of the lamp holders and fitted 4 new 70 watt twin electronic ballasts. Completed necessary wiring within the fitting, new...
This is a new RCD, came in the CU. The max disconnection time I need to comply with is 400ms (Table 41.1 TN ac 230V). From a new RCD I'd expect something roughly in the region of 30ms (for a 30mA fault test). What I'm getting is 234ms (x0.5 there's no disconnection and x5 it's a 13ms...
I have a client who says an RCBO failed in a consumer unit I fitted. They want compensation for the repairs undertaken by another electrician. They never called me first to allow me to rectify the problem.
What rights do they have to compensation does anybody know? I would of happily undertaken...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.