Customer supplied shiny metal accessories, varilight through TLC.
the switch fused spurs are prebuilt from grid components, but where they have put the link, it shows line supply into fuse first, then through dp switch. Neutral only goes through switch.
I thought it would go through switch...
If you have a fuse box attached to your HVAC system is it necessary to have an off switch? Also what does an arc fault circuit interrupter do, and when is it necessary
Hi,
We have an old cooker on the mains with a cooker mains red switch with a normal plug next to it.
The red switch is in the off position as is the plug switch.
Whenever I reset the RCD for the cooker ring in the fuse box, the entire RCD trips again - even if the cooker's red switch on the...
Evening All
Ive got a residential house on a 60a cut out fuse being changed to a 6 bed HMO with 6x 8.5kw en-suite showers.
Im am waiting for a quote from the DNO about upgrading the supply from 60-100a.
I am thinking of useing 2x 3way Garo non priority sub DB's for the showers to reduce the...
A small under counter AEG fridge. Instructions say it is fitted with a 13A fuse in the plug. Also states it must be replaced by a 13A fuse. The fridge is drawing 0.32 amps. A 13A fuse is ridiculously oversized. If having a mcb or RCBO at the CU for just the fridge, a 1.00mm cable can be run on...
Hi All,
Like many practicing electricians I have been frustrated that there is not a simple solution when wiring a bathroom fan with timer and the manufacturer's instructions say that it must be fused with one 3 amp fuse. I believe I have come up with the solution, which I have patented, what...
Hello, can someone explain to me what these are and how they work?
I suspect these are relays that control the electro heaters because the heating dials have an On and Night setting. Or because there is a dial in another part of the house where I assume some kind of schedule can be programmed...
Just a very quick one as can't find anything that answers my question
Doing a re wire and a very old property the main incoming cables come in half way up the wall.... providing I don't run my circuit cables past them is there any reason I can't fit the consumer unit below the main fuse?
I...
I have an older house that was built in stages back around 1960 as far as I can surmise. Highly suspect that the entire house was a DIY job.
I've been unraveling the wonky wiring since day one. The original part of the house was wired with a fuse panel and 12 gauge wiring without grounds. I'm a...
Hello. I have an optima xm6 alarm system. Could someone tell me the best and safest way to check a battery fuse on the board. Do i need to turn off the mains to the control panel or not as the board has an output of only 12v dc being stepped down by the transformer. Would it then be ok to...
Hi,
I just had a new 18th gen with surge protection installed. They disconnected the old cable and did a new run, the cert says 10 gauge was used but then I just had a different sparky who is looking to wire up my garage see it and say it should be 16.
Just wondering what is correct and should...
Hi.
I have been having a problem with my AEG 7000 Series Washer Dryer (L7WEG851R) tripping my main fuse box over the last week. I am trying to diagnose what the issue may be. Here is what has happened so far. The machine is three years old, so it is now out of warranty.
Last week I ran my...
I am preparing for new kitchen and have a new 16amp built in single oven to replace the existing freestanding double oven.
The existing oven is hard wired -this enters wall in a blanked off fitting-which i assume runs up to the Cooker Socket which has an on off switch and a plug socket too...
Hello - I’m a new member here seeking some advice.
I’m purchasing a project property - sadly the previous resident passed away. I’m trying to work out whether I will need to have any major electrical work done or not. The property is fairly run down, but the electrics look like they might be...
I have been to look at a friends flat that he lets out. As result of EICR he had to have the old Wylex fuse board changed for a Fuseboard consumer unit. all RCBO.
This want done by me.
After the electrician left, the tenant complained that the electric underfloor heating was tripping the...
I have a fluke 1653 which gives me a fuse error, but only when voltage is present. Done some research but not found anyone with the same issue... just wondering if it’s time to retire the fluke as I know it’s getting on a bit now...
just seeing if anyone’s had/ seen this before, I’ve tried a...
Hi guys,
my brother is building a bar in his garden that is timber framed and wants some power to it.
The main board in the house has a pme earth and there a no spare ways in the board. From this board there is a 4mm t+e on a 32amp breaker off the rcd side supplying a board in a little out...
Afternoon all. Does anyone know how to remove this fuse. !!! We’ve pulled it, undone the screws But it’s not budging. , it seems like there’s something mechanical holding it in place ???
Hey guys,
I'm 17 and had just bought my first car a 2005 Mitsubishi Triton and noticed whilst driving at night that the 10A fuse for my guage cluster bulbs and parker bulbs had blown. After replacing the fuse, after driving for about 3 mins the fuse blew again. I did some testing and the fuse...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.