holder

Recent contents Top users
  1. LeeH

    Electrical Duty Holder

    Started this course yesterday, down in Kent. Anybody else done it? How did it impact your role at work?
  2. G

    Magnetic door holder

    Hi looking for some help on magnet door holder Have a door in a hotel that requires to be held back on wall with magnet and released on fire alarm activation.can only wire of nearest sounder as panel to far away .it's ctec 24 volt conventional system.undure how to carry out wiring to relay and...
  3. B

    What to do about a wobbly lamp holder?

    The lamp holders on the 2 lamps I have made are very wobbly. Would you recommend a glue? What type of glue? Thanks ☺️
  4. L

    GU10 lamp holder leads?

    Need to source 30 to swap over from Low voltage etc . ANy good deals/brands out there ?
  5. F

    DIY lamp with metal bulb holder - is it safe?

    Hi, I'll start by saying I'm not an electrician (I'm more of a mechanic), but I like to have a go at wiring on occasion. I'm wanting to make a one-off table lamp from an old defunct machine I have, so I purchased some 3 core cable, a UK plug with fuse, an E27 bulb and a 'vintage look' metal...
  6. Nightmer

    UK Earthing a vintage brass lamp to the lamp base

    I have a couple of old metal/brass lamps to which adding an earthed lampholder would be tricky (either the entry for 3 wires is VERY small or the lamp holder is integral to the lamp and is original). All of these lamps have a screw within the base which appear to be for an earth wire - is this...
    • Nightmer
    • Thread
    • adding brass couple earthed earthing fittings holder lamp lamps new old screw vintage
    • Replies: 3
    • Forum: UK Electrical Forum
  7. F

    How to Wire a new vintage lamp holder

    Hey all I just bought a new vintage lamp holder from eBay, I assumed that because it has a metal casing that it would need a 3 core wire cable, but it doesn’t seem to have a place for the earth wire. I’ll add some photos, could someone please help to whether I need the earth wire and if so where...
    • finbowles
    • Thread
    • holder howto lamp lamp holder new vintage wire wiring
    • Replies: 11
    • Forum: Lighting Forum
  8. C

    Separating lamp holder to rewire

    I'm looking to replace the cable on a lamp I bought but I am unable to separate the holder to access the connections. I have tried pushing in the black tabs to release the top but I haven't had any luck. Any advice on the best approach would be appreciated.
  9. U

    wiring metal light holder to old ceiling rose

    Hello there I bought a vintage smoked glass shade chandelier pendant ceiling light and wired it up ok (well the bulb didn't blow) but took it back down because the brass thingy wouldn't do all the way up on my existing ceiling rose.Can i just wire up the metal ceiling light holder...
  10. G

    what Can a restricted licence holder do? And can’t do (south aus)

    What can a restricted licence holder do? And can’t do? (South aus)
    • Gezza13
    • Thread
    • ausie elec holder licence
    • Replies: 2
    • Forum: Australia
  11. J

    Duty holder ___//

    Not sure if this is in the right section but I'm stuck on a 2391 question. What are the responsibilities of the duty holder in the inspection and testing process? A - manage the workforce efficiently B - manage associated risks safely C - manage testing sequence effectively D - manage...
  12. W

    How to open this holder?

    I just cannot seem to "twist" this to open it and replace it with a new one. There does not seem to be any locks or screws holding it. The cord hold is unscrewed, so it is not that holding it.
  13. W

    Need to replace this holder

    This is for a wall ceramic wall light. What type is this and where can I buy it in UK please?
  14. B

    Lamp holder getting hot

    Evening all, I changed the lamp in my dining room (ceiling light) for an LED one this evening. When I took the old bayonet out, I noticed the plastic around the outside of the lamp holder was very hot. Could this just be due to the fact it was an old incandescent lamp therefore giving off a...
    • Beeg
    • Thread
    • getting holder lamp lamp holder
    • Replies: 17
    • Forum: Lighting Forum
  15. M

    Replacing ceiling lamp holder - which wire goes where?

    Hi all I've got a knackered ceiling lamp holder I want to change. It's the type with no flex - the lamp holder is directly on the ceiling mount. But the new one I want to put in will be rose-flex-lamp holder. There are no markings on the old one I'm replacing. So what's the easiest way to...
  16. Nightmer

    Attaching an earth tag to a vintage lamp holder

    I have several vintage lamp holders and would like to use them because they have a good look. I found these earth tags (Earth Tag For 10mm Allthread Rod [PLU95920] - https://www.lampspares.co.uk/earth-tag-for-10mm-allthread-rod) and wondered how to attach them to my lamps for them to work. Is...
  17. Spaniel

    3 phase motor control conundrum.

    Hello, a mechanic friend asked me to check his hydraulic vehicle lift controls as it had failed. When I arrived the lift started working again (of course) but with some contactor chattering upon initial start for approx 5 seconds. He was happy it was working again and wanted to get home, I had...
  18. U

    Heat resistant backing for ceramic bulb holder

    I have recently installed a ceramic bulb holder onto the ceiling of a virarium (a tank for a reptile). The bulb holder holds an infra red heat bulb to provide a basking area for the lizard. The bulb holder is screwed directly onto the ceiling of the vivarium which is made of chipboard. The...
  19. B

    Mirror bulb holder help

    Mrs has a vanity mirror with lights, one holder has packed up any chance from pics you guys know where I can buy one? They are SES holders I’ve looked but can’t find the same as this found ones similar Thanks
  20. Idpost

    Replacement LV lamp holder for Click LV450

    Does anyone know where I might be able to get hold of some replacement lamp holders for Click LV540 12v down lights? The lamp holders are rectangular in shape and are fixed to the back of the fitting via 2 small screws. One of my customers has these lights throughout his house and quite a few...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

Tags

advice aus cable circuit course earth electric electrical electrician hello led light lighting lights looking new please question rcd socket supply switch testing training wiring
This website was designed, optimised and is hosted by Untold Media. Operating under the name Untold Media since 2001.
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock