Hi,
I'm installing a new lighting circuit. Normal stuff - radial circuit with lights looped in on the ceiling roses. My question is - how are things like bathroom extraction fans, smoke alarms or an outside above door light normally included in a new circuit? Are they added as spurs off the...
Evening all,
Long story short:-
My dad has just had an aftermarket parking sensor kit installed on his corvette, is there anywhere that you know of that I could get the wiring diagrams (legally please)?
So far as I can tell. . .
The rear sensors are okay (wired to reversing light), & only...
Hi all,
I am trying to get my head around the current regs regarding smoke heat carbon alarms in rented properties.
for eg could I install.... mains powered c/w battery back up from the upstairs lights, same from the downstairs lights but both are radio-interlinked so both smoke alarms sound...
1. Hi can you please tell me when rewirable fuses in consumer units were phased out.
2. A spotlight bar is fitted to ceiling with original ceiling rose base pushed up into void between ceiling and floor boards. Code C2?
Thank you
midgetman
Thread
ceiling
code
current
floor
fuse
fuses
installed
still
anybody know whats the fuse type for this isolator switch? put one up while ago, customer called and asked to replace with motor rated ones. save me a trip to the site, really appreciated.:yes:
Square D Twinbreak 100A TPN Switch Disconnector Fuse
Anyone installed long lengths of this?
Customer wants it stuck on top of a picture rail around a room (about 20m), there will also be breaks in the picture rail for doors etc.
Just need a heads up on pitfalls with this sort of length required.
Hi
Just to make sure I have this covered, how much space do the DNO & provider normally require for the fuse unit and meter? And what is the preferred height?
KR
Mark
dellboy13
Thread
dno
external
install
installed
meter
position
space
Hi,
I was wondering if anyone has come across this type of situation.
I have had an inquiry from a client with a converted house which is now 4 flats all have had individual ASHPs installed, but each flat is on a sub-meter from the original MPAN meter.
I understand that the MPAN is recorded...
Hi all. Have a single phase cne tnc-s intake inside a lucy cabnet supplying 20 LED sreet lighting columns. Ze @ intake was greater than 0.35 so intake was earthspiked and a RCD installed changing earthing system to TT. @ lucy I have a contactor being controlled/switched by a photocell (located @...
Hi all
I installed an 80kVa diesel generator set with automatic transfer switch awhile ago. All supplied by customer.
Generator is second hand at 50 hours work and it turns out the ATS is too.
All has been working fine for the last 6 months or so but recently the generator has been struggling...
Hi all, just installed a polypipe under floor heating system to an existing Y plan, the valve is a V4073A,with this system the UFH stat should independently operate the UFHeating from the existing central heating, the snag is with the time clock off and the UFHeating stat on both the UFH & the...
Mork
Thread
feeding
heating
installed
position
system
underfloor
underfloor heating
valve
Last week I installed what was supposed to be a reasonably quiet 6inch wall fan in a kitchen.
Turns out it wasn't as quiet as I anticipated.
Anybody know of a quiet one? Must be a 6inch wall mounted one
All help is appreciated
Hi all,
I'm new here so bear with novice questions pls.
I have renewed an old CU (the one with pull out fuses) to a very new one with 2 rcd's and 10 MCB's. the old one had the kitchen sockets and the 1st floor sockets on the same ring (weirdly).
Layout is this:
RCD1 63A with:
1 x 40A MCB for...
Got this come up on a job i'm tendering for. Will speak to designer shortly and get better spec out of her. It has only been specced for the lights - which having read about it seems to be limiting its capability hugely. I get the feeling the only real reason it's been specced is for...
stimpy
Thread
anyone
electrical work
installed
led
lutron
system
received an installation cert from one of the sparks , it was for a new circuit for a washing machine he installed on an exisiting domestic CU , just want to know how much info should be included on the circuit details and results page .
Ive informed him to go back and record all the circuits...
Hi does anyone know of a reason why different makes of smoke and heat alarms can't be interconnected ?
I have several jobs of installing them adding to existing smoke alarms and I haven't been near to the jobs to check the brand already installed? I planned to fit aico .
Thanks
currie123
Thread
alarm
alarms
existing
installed
problem
recommended
replace
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.