instructions

Recent contents Top users
  1. Solark Guy

    ABB (Fimer) Inverter adjustment instructions

    Hi guys, I am new to the forum so be nice! I have this ABB (now Fimer)PVS-100TL 100kW inverter which cut off if there is too much solar incidence. I am sure there is no fault other than threshold setting on control board. Please help me find these instructions or a service manual. I'd rather...
  2. Marvo

    Regs and importance of following manufacturers instructions

    A recent thread on the suitability of a cable supplied preinstalled on a manufactured floodlight/pump had me wondering a few things. Over the years the installation regs have placed more and more emphasis on following manufacturers instructions. I can see this would be fine for higher end...
  3. C

    Assembly instructions for thermostat XT-9605-Dimplex

    Hello , Thermostat XL-8901 was not functioning in a dimplex heater.Placed an order , I received XT-9605 , instead. New part looks similar with the absence of a central hole where , normally goes a screw to hold the part to the unit. Any clear assembly instructions for XT-9605 please ? How to...
  4. Rosecom

    UK Seaward ntb-1 INSTRUCTIONS FOR USE PLEASE

    Help !! Need a diagram as to how to use the ntb-1 rcd tester, not sure as to how to use it with my pt250+
  5. R

    Wiring instructions for buzzer

    Hi Could someone please help with a wiring diagram or instructions to wire up a buzzer to a 10A 1 gang press bell switch. It has L1 and L2 at the bottom and COM and N Loop at the top. The buzzer only has 2 wires. Thanks.
  6. Keith F

    Megger PAT4 3DV instructions for use

    Good day. I am looking for someone who can walk us through using an old Megger PAT4 DV3 machine. We are PAT awareness trained and had a machine donated for use by our local charity, but could do with some guidance, please. Megger can't really assist here. Thanks. Keith Foster 01686 412 048...
  7. K

    Motion sensor instructions says one sensor per switch, Why?

    Hi. I'm new to the board and have two questions about security lighting with motions sensors. 1) I have 2 new LED security lights and 2 new motion sensors. The instructions says to only install one sensor per switch. Both lights are on the same switch and I want a sensor on each light, one in...
  8. Dartlec

    Dodgy Manufacturers Instructions for lights

    On two occasions recently when changing light fittings I've been bored enough (after fitting the light naturally), to read the instructions that came with them... Two different manufacturers (or at least brands) have had instructions calling for terminals to be covered in insulation tape...
  9. S

    Has anybody got instructions for a Wylex smscd11 timer ?

    I’m looking for instructions for a Wylex SMSCD11 timer - can’t find one anywhere and I’m stumped. Client has one that controls a contactor for her heating. I’ve bypassed it for now but could do with th correct instructions. The ones she has are for a completely different timer so it must have...
  10. James

    hot tub installation instructions

    So I have a hot tub to install, in this instance, it is not a problem because there is an existing DB that is TT to provide power for electric car charging. supply to building is PME. have a look at the electrical installation instructions, they are not the worst in the world but I think they...
  11. P

    UK Manufacturers instructions

    The never ending debate about supplies for cooking appliances. ??? I've just received an email from a customer that I'm in the process of quoting for electrical mods is part of a kitchen re-fit. When I first talked to them they were talking about having an induction hob rated at about 7.5KW and...
  12. D

    Wires funny match ceiling fan instructions

    I'm installing a ceiling fan. From the ceiling I have 3 red wires connected to each other only. I have 2 black striped wires twisted together, 1 black wire and 1 white wire. The ceiling fan has 1 black, 1 blue, 1 white and the ground (green). My instructions say nothing about this type of...
  13. Charlie_

    Examples of dubious manufacturers’ instructions

    Astro lighting
  14. garaoke

    Fusing of fans to comply with manufacturers recommended instructions

    Manufacturers want there fans fused to 3a on the permanent feed but the switch wire is still on the 6a MCB doing an eicr is a c2 if there is no RCD protection
  15. W

    BPT Agata VC - Wiring Instructions

    Hi all, We have a BPT Agata VC door entry system and the wiring had come away and I'm unsure on how to re-wire. Any advice is massively appreciated as I can't find any info online. Thanks! Will
  16. oracle

    Diagrams, instructions and circuit charts

    Since regulations 514.9 and 560.7.9 came out it is very rare to find such documents provided, even the minimum of circuit identification on older installations is often not complied with. Can anyone offer a reason for this or is it just too much bother since most guys are using tablets and...
  17. S

    Double ovens and manufacturers instructions

    New kitchen install Integrated Double oven unit Integrated single oven unit Next to each other Existing circuit 6mm 32A mcb New double oven manufacturers instruction 40A fuse hard wired New single oven manufacturers instruction 16A fuse hard wired Existing cable too short for new isolator...
  18. S

    LED Transformer - No Instructions Supplied

    I purchased a 100w LED Transformer (240v - 12v) from LED Hut. It came with no instructions. I contacted customer services and asked if I should switch at the input or output side of the transformer. The transformer has 2 outputs. I also asked LED Hut if each output was limited to 50w or if...
  19. D

    Junction Box Instructions

    Found this under the floorboards of a house. Was wondering what year it was and if anyone remembers installing the Tenby R.M.1?
  20. sjhall

    Can anyone help with make and instructions

    Need instructions for this timer Can anyone help ? Thanks

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

Tags

advice aus cable circuit course earth electric electrical electrician hello led light lighting lights looking new please question rcd socket supply switch testing training wiring
This website was designed, optimised and is hosted by Untold Media. Operating under the name Untold Media since 2001.
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock