Good evening
Was wondering when testing for.insulation resistance and there is vulnerable equipment in circuit but unable to disconnect, I understand that you combine the line and neutral conductors and test to earth. I am just wondering if it's ok and safe to do this at 500v as there is no...
As it says really. When testing LE or NE resistance > 300M ohms but between L and N I was getting a reading of about 0.2M ohms. Could it be the BG cooker switch that has two neon lights that is the problem?
If it is, after shoving 500V dc through them, should I replace this erstwhile brand new...
As in the title.
I need downlights that can be covered in insulation, fire rated and integrated.
Preferably quite shallow as well!
I'm struggling a bit to meet all the above criteria :(.
Cheers guys.
Does anyone know about how much of a void in insulation is required for lights like these?
Putting downlights in a loft conversion and if I install standard size ones I'll be creating some serious cold spots...
I’m currently problem solving a lighting circuit issue on a retail park.
newish install (12months old) IR of 12M Ohms across all three conductors, getting some very odd IR readings overall, I got a low reading between two separate disconnected cables, sent my meter off to be calibrated and came...
Hi, I'm not an electrician but I'm studying the material required for the C&G 2394/5 just for the sake of it. I think I understand the theory behind insulation resistance testing (but maybe not!) and the reason the test is performed at 500V (insulation condition, fault finding) and that loads...
I need to insulate under my suspended floor which has many cables running through the joists (consumer unit is below floor). My main concern is causing the cables to overheat etc. Here's a quick overview:
Joist height: 140mm
Cables: Mixture of circuits but the 2.5mm 32A rings are my main concern...
With regards the title is the reason for this because the circuits are all in parallel?
I am talking in relation to a L/N - E test.
If Rt = global resistance for whole CU and R1, R2, R3 = L/N - E resistance for each circuit then am I right with the following:
1/Rt = 1/R1 + 1/R2 + 1/R3
So...
Hi all,
Just installed a brand new radial circuit for the upstairs sockets with Prysmian 2.5mm T+E, around 21 metres in length. When testing the insulation resistance of the circuit upon connection to the consumer unit, I seem to repeatedly get around 49 Megohms when measuring Neutral to Earth...
Hi guys
New build small 2 bed bungalow to have 300mm of insulation in loft space. Obviously all circuits to be ran in loft and dropped. Circuits to be used are alarm circuit 6amp, lighting 25x 4w downlights 6amp, 2 x 32amp ring mains, 16amp boiler radial, 32 amp hob/oven circuit (undecided if...
Hi - I have a Warm-up underfloor heating system. And it's stopped working. I did a basic resistance check - and clearly there's a problem (shows just 18ohms when it should be nearer 200). Warmup have said they can send an engineer around to lift a tile after doing a thermo heat check...
Hi gents
Whilst I am qualified as an electrician I am a maintenance engineer so don't do much installation work hence seeking advice here.
I recently installed a new 3ph distribution board for a new machine. As I don't have my testing and inspection ticket another person did the minor works for...
Hello everybody,
I'm an intern and I'm searching about Insulation Piece in solar panel. This word is new for me and I didn't find anything about it. Can you give me some link about it?
You help is very important for me!
Hope you are happy and healthy!
Thanks everyone.
I'm doing a garage conversion. 70mm insulation on block then an inch gap battened on top, then 35mm insulating board. Where's best for the cable to go in terms of derating etc...
Cheers.
Hi
Has anyone had any experience regarding insulation in walls on new builds as to what size mcb they are using for ring main circuits. I have checked the regs and seen that 100mm > insulation derates the cable capacity a fair bit. The builders are using 140 mm in the walls. I have pointed this...
Hi, I’d like some clarification with regards to insulation resistance results I’ve got.
Carrying out initial verification on a new ring final circuit. New cable, 9 new MK double sockets.
r1 - 0.43
rn - 0.42
r2 - 0.68
R1+R2 - 0.28.
Carried out insulation resistance test:
L-N - >2000 MOhms
L-E...
So I'm currently sorting a CU change and kitchen rewire while also fixings some bodges by a have a go client, came back this week to discover that he has decided to insulate the void between ground and first without mentioning it. Now this has derated all his cables by half as they are tottaly...
Doing new supplies for a school new Shneider 3 phase & N MCCB panel board. 50mm 4 core SWA one end made off in the board earth fly lead from banjo to earth terminal. The other end gland made off in gland (fly lead not made off yet) 3 phases and neutral just hanging there. Done installation...
Toneyz
Thread
cable
insulationinsulation resistance
insulation resistance test
length
resistance
swa
test
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.