Hello,
I bought an air conditioner 24000 btu Inverter. The indoor unit makes strange noises/sounds at night.
The pattern is as follows:
First, wind blowing and cooling are reduced to 80%. (Similar to fan mode)
Then the sound (sound in the video) comes a few times and then everything returns to...
Hi folks,
I have recently had a 5kW Solis inverter and 15kW/hr of batteries installed. Everything is working fine, but I have some concerns about the quality of the install:
I wasn't given any documentation, so no "part P" documentation.
Around three metres of new meter tails were added -...
Hi guys, I am new to the forum so be nice!
I have this ABB (now Fimer)PVS-100TL 100kW inverter which cut off if there is too much solar incidence. I am sure there is no fault other than threshold setting on control board. Please help me find these instructions or a service manual. I'd rather...
Hello everyone. I have a inverter configuration problem I thought someone here might be able to help with. I'm not looking for a specific solution for my inverter in question, but rather if anyone has encountered this problem and has generic parameter advice to give.
I'm using a Mitsubishi...
Hello,
So I purchased a Novopal 2000w/4000w(Peak) Pure Sine Wave Inverter DC 12V to 110V/120V.
I purchased this so I can hook it up directly to my truck's 12 volt battery and have it positioned in the flatbed of my truck..
The goal is to have it power my microwave in my flatbed at drop sites. I...
So I'm looking to connect my car's battery directly to a Pure Sine Wave 2000w power inverter So I can use it on job sites etc to power a microwave of above 1700 watts.
My question would be, Do I need to have a one-way fuse in my wire setup directly from the battery to the inverter? Or can it be...
G99 GSI-3 4.4 kw Victron inverter install with EES and batteries and installer can set the export lint if required by dno
As part G99 GSI-3 you required carry out phase to neutral loop impedance and phase to earth loop impedance test not a problem. but the must be 180 m ohms or less for...
Hello - hope someone can advise please.
I have a recently purchased second hand Myford lathe which has a 3-phase inverter (Siemens Micromaster 410)
Lathe all works fine but regularly trips my RCCB 80A 30mA breaker taking out half of the board - usually when first powering on. The inverter is...
I have been asked if I can wire a motor for a car lifter in a domestic garage, however the motor is 3 phase and only single phase is available in the property. Is it possible to use a single phase to 3 phase inverter to power this motor? I will attach photos of the motor and its output.
Hope this all makes as much sense as i can make of it and my "problem" can get sorted via some guru on here...
Just a quick background on myself, i am fully qualified and have been for 15+ years. I have completed the 18th edition and am a member of the approved and domestic installer schemes on...
We don't normally do PV, however I was called to a PV inverter with no power, 6 years old
Found supply OK, however fed through a AC type RCD.
PV inverter has power, no display etc, no fuses blown
Supply Zs OK, voltage at strings (about 260V in afternoom, east west split)
DC and AC isolators...
Hi there I’ve only seen inverters for solar energy or camper vans …I’m looking for information
On buying an inverter using a water power wheel using an alternator. A lot of the videos don’t give the precise instructions needed.
Also a question about getting power from an inverter 220v to about...
I don't "do" solar, but I've been asked to comment on an aspect of a new domestic solar installation by others.
There is no overload or fault protection, except for the service cut-out fuse (unknown size, assume 80A). TN-C-S.
Installation is as follows (have only seen a photo of part of it...
Hello everyone, I currently have two solar modules left over from an installation and I would like to use them to set up a solar system on the balcony. The system has an output of 800 W. Can you recommend a suitable inverter for me? Thanks for the help.
I have an 5kW inverter and 48V Lithium battery with inbuilt BMS. As you would be aware, when inverter gets battery power, immediately the capacitors in inverter start charging drawing very high current. This causes BMS to trip thinking it is short circuit. Battery company suggests using a...
Hello,
My current 2.5kW Solar pv array is in a less than favourable position, but there is plenty of space to expand the array. I have an additional 4kW of solar panels that I wish to add to the array as even during peak production we are lucky if we can achieve 1800W out of the 2.5kW so...
I am installing a Victron Quattro in an island mode configuration (in the UK, the DNO is the NG). I will be adding a stand-by generator. My property has a standard TN-C-S (PME) earth arrangement. I am an electrical engineer (testing) not an electrician. The regs state the DNO earth cannot be...
Hi,first off this does not relate to work I intend to DIY. I'm trying to sanity check information I've been asked to provide to the installers.
I want the solar invertert to connect in the garage, where there's a DB fed from the house via SWA.
This is what's asked ..
As the proposed PV...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.