isolate

  1. GeeWizz12

    When to isolate incoming supply to DB

    I always turn off main switch before removing cover or doing any work in a DB, but when should incoming supply be isolated ? When placing a clamp-on ammeter around an incoming phase conductor in a 3 phase board a spark to board casing occurred. Later found to be pre-existing damage to insulation...
  2. Qwe7410

    How to keep power trips isolated and not trip the whole place when testing faulty appliances?

    Having some 1400W 230V heaters to test and repair that have a power trip problem. I've unplugged all the connections and open them up one by one to identify the part that is causing the trips. Everytime it trips, it trips the whole place through the main circuit breaker. How can I do it safely...
  3. S

    How should you locally isolate the supply in a garage

    I’ve just moved into a new bungalow. The 6mm T&E cable supplying the garage goes to a FSU with a 13amp fuse. The FSU feeds two double sockets and 2 LED light battens in the garage. The supply is protected by a 16amp mcb backed up by a 63amp 30mA RCD from the consumer unit which is located in a...
  4. Msitekkie

    UK TN-S Looped supply - earth upgrade. Need to isolate neighbour/refer to DNO?

    I have come across what I think is a looped supply - like a normal incomer but two of them coming up side by side. It's a TN-S arrangement with an earth cable looped between the two incomers and on the the consumer unit. Trouble is it's only about 1mm, although I got a decent ZE of 0.35. It...
  5. Sboyuk

    Isolate ring main extension.

    Hi all, I hope you can help, I'd like to extend a ring main into the an outbuilding and be able to isolate it if required. I'll be using power tools and wanted about 4 double sockets in there so didn't want just a spur. I've attached an image, is this an acceptable way of doing it.? The...
  6. w0z

    Recall: Proteus Switchgear - 100 Amp Double Pole Isolator - which might not isolate.

    Disconnect once check twice..(or more) Found HERE at Trading Standards Risk level Serious Risk type Electric shock Risk description The fault was identified during routine installation process which includes a test. It was found that the switch did not isolate the circuit. The product does...
  7. J

    To isolate or not to isolate…

    I have a new TP pump install, the supply comes from a 80 amp switched fuse disconnector from the road straight from the supply tales via a 5 core 35mm. Into a specially built housing within which a controller with inbuilt isolator is situated. I was going to install a separate triple pole...
  8. N

    When working on circuits do you isolate whole board or just the final circuits using MCBs ?

    When working on circuits do you isolate whole board or just the final circuits using MCBs ? Or is there any instances when the whole board has to be isolated even if you are working on few final circuits? Thanks.
  9. A

    Confirming earth bonding continuity when cannot isolate supply

    Hi, just wondering how other sparks, go about confirming main earth bonding continuity when supply cannot be isolated, ze and pfc can be enquired wich is fine but what happens if you cant disconnect main bonding earth, is previous test results good enough to confirm?visual checks good enough...
  10. C

    How do I isolate 2 switches for 2 devices?

    Hey all! I'm trying to find the best way to wire a dual switch for a porch light and indoor ceiling fan. The source power cable, fan power cable, porch light power cable, as well as a smoke detector power cable all reside within an accessible metal j-box (see attached drawing). I currently...
  11. J

    32 amp rotary isolator

    Anyone know if there is a reg in regards to supply going in to the top of a rotary isolator. We are changing the isolators over for ac units, long story short they won't reach the top terminals now, so feed can only go in bottom. Just a 2.5mm 3 core swa. Cheers
  12. mak

    Schneider board main switch TP-N and 4-pole

    What's the difference between the two, one isolates N the other does not, got me confused when I was testing continuity between E-N, then I realized N was not isolated.
  13. J

    Safety - does switching off at consumer unit isolate the circuit switched?

    I am not an electrician (as you will see from the question!) and I am not planning on doing any electrical alterations. My question is one of safety. I wanted to move a couple of sockets on a kitchen ring main. So I switched off that circuit on the RCD board and all the sockets were then dead. I...
  14. Pete999

    ISOLATE

    Sorry for starters if this is in the wrong area, don't know where else to put it, I take no credit for this just saw it in PE and thought it may be useful: So ISOLATE I identify circuit to be isolated. S seek permission to turn off. O Open circuit L lock off and label A Approve voltage GS38...
  15. M

    Two ceiling rose one switch - Please advice

    Hi guys, I'm trying to figure out the wiring of two ceiling rose with one switch but I can't figure it out. Would appreciate any advice. I have identified which cable is which but can't figure out where the 2nd ceiling rose cable goes. Right now the 2nd ceiling rose is always on and 1st...
  16. A

    Fixed wired testing in situ

    I have got some heaters etc to do and after reading my PAT420 manual it can test fixed wire equipment in situ. It will do continuity test @200mA and touch leakage. Would this be OK or do I need to connect it to my tester? I have read a lot but I would like some opinions from people that have...
  17. G

    Isolate Light to find Live Plug

    I Went to isolate light & found this. This has been rectified. What further action would you take?
  18. sparky1508

    Switching non timer extraction fan

    Hi, Can't seem to find anything in the regs but I have been asked to fit an extractor fan in a small cupboard containing some IT equipment which gets quite warm and it's just to dissipate heat out of the cupboard. My question is, as it's a fan without run on timer I am using T&E to power it...
  19. Irina Nistor

    isolate manes

    I want to change my Consumer unit inside my flat ( I live in a 8o flats court) and in the image is the meter and a switch. AM i allowed to operate this switch on my own off to change my consumer unit and on after. or will I have to inform DNO or other authorities? thank you
  20. J

    NICEIC Certification Scheme safe isolation- the niceic way!

    niceic initial assessment tomorrow! woop woop Seek permission to isolate isolate, locked off with signage- keep key on you prove my gs38 approved voltage indicators on a known source (will use supply side of main switch?) test between L-N,L-E,N-E for voltage re-prove voltage indicator on known...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
This website was designed, optimised and is hosted by Untold Media. Operating under the name Untold Media since 2001.
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock