Should a small 500W electric rad on a fused spur also have an isolating switch?
Some of these small rads have fancy timers that might get confused if switched off at the wall rather than their controls.
Hello. I'm new here and greatly appreciate any assistance that more qualified persons can provide. I am a DIY person with some, but limited, experience handling transformers and other high voltage items in electronics. I have a deep respect for their potential to harm and I like to be very...
Something is causing 1 bank or RCD (80A 30mA WRS80/2) to trip on consumer unit, intermittently. I think it may be the fridge freezer, but can't be sure. Is there a plug in unit (lower fuse rating) that I can insert between the fridge and the plug point that will trip before the consumer unit...
I’m due to return to the UK next Thursday from Belgium and want to confirm if I need to self isolate away from my own household? My wife is saying I need to stay on my own for 14 days after my return before I can go home even though I have no symptoms. I’ve tried looking online and can’t find...
I have 400 Amp service split into two 200 Amp panels. I’m converting one to a protected loads panel as part of a PV solar system with battery backup. Since ground is tied to neutral I want to isolate the neutral and ground buses of one panel from the other to make sure no current flows to the...
Thanks for adding me to the forum.
I have done quite a bit of electrical work around the house adding sockets, and at our current house I put in some new ring mains and lighting circuits, all subject to third party certification and with the new consumer unit installed by a qualified...
Hello
First time here. I was just wondering if any one can give me a bit of advice.
I’ve removed two wall lights in the living room of an old uk house. I’ve isolated the live feed to the lights from a double switch and was intending to isolate all of the wires however I can’t find where the...
As can be seen from my profile I am not a qualified electrician but I'm studying in my own time just for the sake of it. Everywhere I look for info on isolating transformers I get something like this "This means that the isolation transformer secondary side must not be grounded. It would create...
I am installing final equipment in a new electrical installation and our equipment is fed via a local 3-phase 1:1 isolating transformer (Input is wired Delta and output is wired Star). Our equipment is all single phase and split across the 3 phases. It comprises many switch mode PSUs.
I have...
I am planning to move a socket outlet. The CU is largely unlabelled so don't know which 32 MCB to switch off. There are 2 x 32a MCB. All other mcbs are for lights (6a) and a dedicated immersion (16a).
To isolate the circuit, I tried switching off the first of the two 32a mcb which isolated some...
With the ease of EICR's and the like, and for customers to isolate those "buzzing" shaver sockets, isn't it time we started fitting them on isolator switches, either existing fan isolators or fused Spurs?
Can't believe some electricians still hang them on the live lighting circuit without any...
Hi, I am having internal damp work done and have been asked been asked by the contractor to prepare by isolating the electrical wall sockets and removing the faceplates and sockets. I have 3 double, surface mounted sockets to isolate. There is a short section of trunking from the floor boards...
joe99
Thread
blocks
damp
electrical
electrical work
isolating
plaster
removal
sockets
work
I'm currently minding our neighbour's house and animals whilst they are abroad for a month. The kitchen lights are suddenly causing the downstairs lighting circuit to trip. When I reset the switch all other lighting, lounge and hall work ok, but if I try the kitchen lights then the circuit...
Hi, Does anyone know how much it costs to get the local authority to come and isolate the supply to a domestic house. While we fit a DP isolator. As part of the contract we are not aloud to cut any seals. Thanks
Hey all
i know you have to install a cooker switch to either side of the cooker in a new install. However in an existing install where it is positioned above the cooker does it say anywhere that it's illegal to have it there and does it have to be moved. I know it's dangerous as if there's a...
I've just looked at a job in a residential home where I need to replace a sfcu. The circuit is on a old cu and I've noticed that the main earthing is in 6mm and has thermal damage, I've quoted to also upgrade this. My question is the cu is on a SP TN-S and has 3 cu coming direct off the supply...
Hi all, our NIC inspector came round recently, and one of the changes we had to make was to the way we 'control' fire panels. Previously we have just fed the panel from an unswitched fused spur. However according to the NICIEC man this is no longer acceptable, so what we have to do is fit a...
I need to protect a digital welding inverter from voltage spikes when powered from a generator, iv'e been told running it through a transformer will do this, however the welder is 240v and the only transformers i can get at a sensible cost are 240 in, and 110 out site transformers, i could get...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.