Hello and thanks for the interest. I have a little dilemma and was unable to get an answer anywhere.
I'm trying to fit a SPD and an over/under voltage protector to my existing "Main Switch" and "RCD" setup. my question: is the location of the SPD and surge protector correct? thanks
Hey all, I've got a question about a new apartment I'm getting. I recently had a home inspection done on it and the inspector noted that my panel was double tapped and drawing what might be a little too much power for its rated size.
The apartment is a 700 sqft one bedroom and all appliances...
I purchased an old farm property and am have been going over what would be the best approach to tackle this job. The house has been in use by myself only for over a year with no issues (fires) yet and it is wired for 100A service/#2 wire. I don't want to push my luck so I am going to work on...
I live in the Philippines but I have the same US electrical system (2 x 110V hot + 1 x neutral). I have two ground rods buried 8 ft. deep and connected to the main panel. Netural and ground are bonded in the main panel. And from the main panel, all 4 wires (2L + 1N + 1G) go to sub panels. Ground...
Hello all - I have a 60 AMP sub panel that services a few 15 amp circuits and 3 240V A/C Compressors. I want to use a portable generator to run everything EXCEPT the A/C. What I want to do is connect the Generator through a DPDT transfer switch to the Circuit in the main panel that services the...
My client has bought these 'antique' lights, stop sniggering at the back, but they are incomplete.
Anyone know what the missing part is and if they can be bought separately?
1599753322
Is this the kind of thing that's needed?
So I am choosing my downlights and I was looking at the cylinder shaped fire rated downlights. The electrician mentioned look at LED slim recessed downlights as my new plasterboard ceiling would not be able to hold the weight of the standard fire rate downlights.
One thing I didnt clarify - who...
Hi. Wondering how bad (or OK?...doubtful) of an idea it is to run some 14-2 from an existing outlet, underground in PVC to a new sub panel in a shed. The run would be about 20 feet total. I just need one circuit in the shed. Will be running 3 outlets and 2 LED strip shop lights.
Anyone know what height a fire alarm panel should be mounted. Just a basic off the shelf 4 zone panel. Plenty of information on call points and heads but contradicting heights found for DDA.
Hello all. Thank you in advance for any guidance. I am in south Florida and I am a DIY person. About a year ago, I hired an electrician to install a new exterior main breaker panel and also a new sub panel in the garage. The house was built in 1975 and had aluminum service wires. The...
I have an Eaton 125 amp panel with a ground bus bar with 24 slots and 14 neutral slots. I have a 6 breaker Reliance 7500w transfer panel connected to it. The main panel has 4 unused breakers. I need to increase slots on my neutral side. Can I add an additional neutral busbar to the existing one?
I noticed some brackets along the sides of two breakers in an Eaton BR panel board.
One is along one side of a 20A Type BR Combination AFCI breaker (labeled for the dishwasher and disposal), and the other along one side of a double 40A breaker (for the Range).
They look somewhat similar to a BR...
My guvnor recons that all submains from the main Distribution Panel, should go via metered supplies. Although they are all for one customer who owns the building.
Any reg on this, as I would like to look it up! Whether BS7671 or a Building reg.
Hi,
This is a 10 year old 10 panel installation, recently output has been droping and somtines reaching zero mid afternoon. I think it is a sunnyboy inverter. Does it look like a panel, inverter or high mains volts? Could I have names of installers in West Yorkshire who may be able to help.
Thanks
Hi guys.
Unfortunately due to the coronvirus the the house I was going to be building is now on hold. Due to this the solar panels I previously bought are now for sale.
I purchased this from the wholesalers for £1600 and am open to offers. Its all brand new still in boxes.
Included are:
8 X...
Hello all, after some advice please.
I have got a small job installing some 16a commando sockets in a farm workshop. The workshop has a 3ph sub DB on the wall which is fed from the main DB on the other side of the wall, about 25m away. The sub DB is supplied from two lots of 6mm2 twin in 25mm...
This a question from a Complete Newbie! Please bear with me!
I have a 2.5W; 8.7V small solar panel, but of unknown I-V characteristics. It has been very difficult to trace manufacturer's sheet.
THE particular quantities needed urgently are: (1) THE NUMBER OF CELLS; and THE REVERSE SATURATION...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.