You turn up to a property that had recently had an EICR, reporting that the water had no bonding.
The main water stop cock and on-wards was plastic push fits with maybe 400mm lengths here and there (downstairs), but upstairs is still all copper piping behind bath panel and sink pedestals to 2...
After your thoughts on EICR coding for an existing plastic consumer unit in an under stairs cupboard, firstly in a standard domestic dwelling and secondly in a house of multiple occupancy.
After discussing this others and with tech helplines seems to be a bit of a split as to what code!
Hi guys, Been asked to run a circuit for a hot tub the board is an MK Sentry (the old one with the plastic cover) but all of the RCBOs fitted in the board are Lewden :confused: thoughts on fitting an MK Sentry breaker (cause thats the manufacturer of the board or a Lewden breaker (so they all...
Under the 18th there is the new line Regulation 411.3.1.2
'Metallic pipes entering the building having an insulating section at their entrance need not be connected to the protective equipotential bonding.'
Got me thinking as in the last half hour a regular customer has rung me up asking if I...
I was just reading an interesting post about the 18th when the above was mentioned. there seems some debate about this. I initially thought that the idea of prohibiting the use of them was stupid, but I'm not sure now...
Hi to all. I'm new and this is my first post.
I'm doing an EICR on a 3 story building split into multiple offices to let.
One thing I noticed is t+e cables in plastic trunking almost throughout (switch/socket drops, across ceilings to lights etc).
Would this be a code 2 or 3? Also would same...
Hi all
Having a thumb through the OSG and on section 4.5 Main protective bonding of plastic services, it says there is no need to bond an incoming service of the service pipe is plastic....thats kind of a given....my struggle lies on the next page;
"Where there is a plastic incoming...
I've always been a keen recycler, both at home and work. Charging for plastic bags, I think was a good thing. Everything seems to either be wrapped up in plastic film, or in a plastic container.
News this week, that our government is considering a ban on plastic straws and those things you...
Hi all,
I've tried to find the answer to this question, but I've drawn a blank.
Situation... location is a barn, attached to a domestic property. This will be a sub-board supplied in T+E from the main board in the house.
The question is... is a plastic board acceptable or should it be metal...
I need to replace some plastic light switches and would like to use metal replacements. The old switches had no provision for an earth wire and most of them had a sleeved unconnected earth wire which I was able to utilise. However, in three of the back-boxes the earth wire was cut short, is it...
I know it's bad practice but.i opened up a plastic light fitting 2 stories up on the external wall and there's no earth just line and neutral.i feel it's okay but is there many reasons this is bad
Hi. Quick question. Domestic property recently rewired by niceic spark. Water incomer is metal for about 3 feet into the property (celar) but the rest of the water installation is plastic. Looks like during the rewire the water bonding was broken on purpose. Does it need to be bonded again? (My...
Bending Springs for plastic conduit someone once said to me that you should tie on end loop and bring through spring it stops it deforming when pulled out.
Hi all; a stand alone RCD enclosure, is this classed as "similar switchgear assemblies" in regards to reg 421.1.201 and so needs to be made of metal ? Im considering that a stand alone RCD and its enclosure might have a different BS number and so might not apply to this reg ? Anyone know...
I've tried to find a solution on here to this exact scenario but had no such luck.
Could somebody please advise on where I should place the earth wire on a plastic back box with no earth terminal when adding a new metal face plate? The face plate has an earth terminal on it and was probably...
DKenny
Thread
back box
box
connector
cpc
earth
light
light switch
metal
no earth
plastic
switch
terminal
As a project I am interested in getting some Liquid plastic, the sort you could possibly recover or repair insulated tools with, I realise it won't be up to VDE standards, but would like to give it a try anyway, anyone got any ideas as to where I can get some? tried The Shed, Wickes etc.
Hi all
Currently working at the block of flats(5).No gas supply to the building.Water all plastic from incoming supply to throughout the building.Can we omit the protective bonding to all the flats.
Any information will be much appreciated.
Although I did not instigate the work outlined below, I need to give feedback to a committee if it is incorrect so your observations would be appreciated. Location is within a church
2 x Metclad boxes/faceplates with fused spur required change over to switched spur.
After the work had been...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.