roller

  1. Kallo444

    DIY - replacing manual shutter roller wall switch with smart one

    Hi Everyone, DIY advise required here please. I have the following wall switch, currently wired in as below and controlling external roller blinds. Inside the wall view has additional wires. My DIY project is to replace the wall switch with a smart one below And here is my wiring...
  2. W

    Isolation switch position for warehouse roller door

    Hi, I am not an electrician and looking for some electrical advice. We have had a new electric roller door installed at our warehouse. The door opening is 4.5m high and the motor for the door is at this height. The electrician has put 3 phase power supply and isolation switch at ground level...
  3. B

    Roller Shutter Switch swap to 3 Gang Switch

    Hello Everyone, (NOT DIY JOB, Need advise prior to calling an electrician on site) Is it possible to swap a 3 phase rotary switch (roller shutter switch) to a 3 gang touch switch? left button for up, middle button for stop position and the right button for down. Would like to utilise a Deta...
  4. I

    Electric roller shutter

    Morning! Any reason why it wouldn't be possible to have two roller shutters connected to one spring return key switch? Both shutters fed from the same circuit, currently have 1 keyswitch per shutter but a customer wants 2 on one.
  5. P

    roller shutter

    are they supplied from a power circuit or is a light circuit ok . assuming the motor is well under any power load issuies
  6. G

    Roller Door Feed 3 phase (RCD?)

    HI all, changing a board in a commercial warehouse and they need a 16amp feed to a new roller door, there is an armored there that will do it and I'm fitting a new shnieder board with RCBO's, am i best fitting a 3 phase MCB in the board or a RCD commando by the door? Cheers Grand
  7. Dean. Sinnett

    two way switching for roller shutter door

    Hi All, Can a roller shutter door be operated from two positions, inside and out? There is currently a key switch outside and would like an up/down switch inside if possible. Any help with this matter is appreciated. thanks Dean
  8. D

    Australia How MUCH to charge to wire up a motorised roller shutter?

    I got my a grade licence a few months ago, so I'm sorta new to giving quotes and stuff. A 'good' friend of mines dad(step-dad) installs motorised roller shutters(labourer, not an electrician) for a living and asked me(through my friend) if i could wire up motorised roller shutters for him. $60...
  9. S

    Roller Shutter issue

    I hope this is the correct place to post I have a external electric roller shutter. it was working fin until last week my son accidentally gently reversed in to the shutter whilst it was opening. no visible damage ie bent slats etc Now it does not fully open stops 2 ft from fully opened. iv...
  10. K

    Roller shutters UPS advise

    Good morning , My name is Martin and I hope someone can help. I am planning to install domestic roller shutter onto our home. At first , I was going to appoint an electrician to run the wiring from the shutter motors to the lighting circuit, but then I realized that I need an emergency power...
  11. K

    24v DC electric roller blind

    Hi everyone, I'm a total novice, so apologies if this all sounds obvious & easy!!! I'm wanting to install a motor to my roller blind & have found a 24v motor kit on amazon. Issue is it only comes with 2 bare wires from motor & needs wiring to plug into a 24v ac adaptor. Tried looking...
  12. keniff

    roller shutter switch

    hi guys, i have been asked to swap over a key switch as its damaged, when i opened up the switch its not your typical common with 2 no contacts, it has one NO contact and one NC contact, can anyone explain how it works? im just swapping like for like but just don't understand how it works with...
  13. Y

    Roller door not working

    Hi guys, I have a 3 phase roller door not working. These are my readings? L1-L2 418v L2-L3 419v L1-L3 415v L1-N 134v L2-N 255v L3-N 247v After checking L1 and Neutral I thought it was a neutral problem but why is it ok for L2 and L3?!?! Thanks
  14. S

    Unattended closing and opening of roller shutters

    Hello, I am looking for a little help for a solution for a client who wants to close and open security roller shutters remotely. The brief is: serviced office with 6 electric roller window shutters fitted, they need to close window shutters after the building is empty and open in the morning...
  15. T

    Roller Shutter stuck in the half way position

    Hello All, just posted the same in the introductions forum but thought you more experienced guys may give me some assistance. Appreciating this may not be electrical specific, last evening my roller shutter (patio door type) stuck in the halfway position. The switches are buzzing when operated...
  16. T

    Roller shutter stuck in halfway position

    Hello, new to the forum and thank you in advance for any assistance. I have a large roller shutter on my patio doors, which last evening stuck halfway. There is a buzzing sound from the control buttons. I appreciate it may not be electrical specific but can anyone advise how the shutter is...
  17. HJC

    Changing Roller Shutter Switch

    Hi everyone, Need advice on replacing roller shutter key switch with a regular up/down switch Client doesn’t want the key switch and prefers a rocker. Would this be a straightforward swap? Or should I leave to the roller shutter crew. Thanks
  18. M

    Electric roller shutters - 2 new switches don’t work the single shutters from 2 switches.

    In my house in Spain, I have just replaced 2 switches that controlled a single motorised shutter (the pair of switches in photos - NB, shutters are the middle of the cluster, other 2 being, 2-pin socket and a light switch) on a bed headboard that controlled a motorised window shutter. The...
  19. R

    Security Roller Shutter Door Isolator

    Hi All I'm trying to find an isolator that will take a class 4 security padlock for a factories roller shutter door, this is to comply with their latest insurance assessment. Can anyone point me in the right direction please? The usual 16/32A rotary isolators do not have a big enough hole for...
  20. D

    Newbie Handyman looking for advice about electric roller garage door switch!

    Hi, Please excuse the 'jump straight in' thread! I've tried looking all over the internet for a solution to my problem, but can only find links to Landlord and Tennant issues!! I have an electric roller shutter door on my garage that has been installed for a number of years. I used to be able...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
This website was designed, optimised and is hosted by Untold Media. Operating under the name Untold Media since 2001.
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock