settings

Recent contents Top users
  1. cliffed

    Rcbo tripping on 1/2 settings

    Rcbo tripping on 1/2 settings with load connectted but ok when load disconnected all other tests are fine… FI required but any thoughts on this😎
  2. H

    help with my boiler settings!!

    Hi I'm in a bit of a pickle trying to set up my hot water and central heating systems. Got a gas boiler with a pressure tank and a motor circulating the hot water. There are two wall-mounted time adjustment thingies—one for hot water and heating, and the other for the motor. Oh, and there's a...
  3. J

    Settings needed for Horstmann Electric 7 boiler for best use for 1 person, without economy 7 tarif.

    I have been living in my two bed apartment alone for three years and can never get the settings on my horstmann boiler so that I have enough hot water. I don't work so I'm at home 24/7 and use more than the average one person's consumption of hot water, I like to take a bath daily and do lots...
  4. BiddeldyBwah

    Do 3 phase boards usually have RCD protection in commercial settings?

    Just sat contemplating life and realised i don't think i've ever seen any RCD protection on the boards we maintain/install at work. I've seen 300mA protection on some section boards but don't recall ever clocking a 30mA in a 3 phase board. Am i just not looking properly?
  5. Rob Plant

    Why do mA and A settings on multimeter give different result?

    With apologies in advance for the newbie question... I'm using a multimeter to figure out the source of my battery drain, so attempting to measure the leakage current between my battery terminal and its lead. When taking the readings shown below, they are quite steady, but as you can see, on...
  6. T

    D.O.L starter overload settings

    Hi everyone ive got my AM2 coming up and im unsure about the over load settings for the D.O.L, ive seen 2 different equations and im trying to work out which is right. so say my motor is 750w would my calculation be 750/400/1.732/0.8 = 1.35 or 750/400 x 1.732 x 0.8 = 2.59 i bought a course...
  7. Zdb

    List of torque settings

    I don't suppose anyone has put together a spreadsheet with a table of torque settings for popular/common brands/devices? Hoping to save some time if it's already been done and shared here Many thanks
  8. J

    Veritas R8 settings options

    We have a veritas R8 with remote keypad. Currently there is the one pass number which allow users to set all/part of the system. I would like to add another passcode which has a different range of zones. So say a master (1234) - which will set/unset all 8 zones - or part plus a visitor (5678)...
  9. R

    I would like some help to bypass a touchscreen climate control (strictly fan speed and vent settings (eg, floor/dash).

    I would like some help to bypass a touchscreen climate control (strictly fan speed and vent settings (eg, floor/dash). Background - 2003 Acura mdx. For some idiotic reason Acura designed the climate control fan speed and vent configuration into the touch screen. Not a terrible thing but...
  10. B

    Settings on veritas r8 alarm

    Apologies if this is the wrong forum thread. I have installed myself a Texecom veritas alarm system. it’s either the r8 plus or excel, as it has a shared manual and no mention on the remote control panel. I initially was trying to change the part set bell delay, but concluded it’s not...
  11. B

    Texecom Elite 24 control panel Resetting to factory settings.

    That's a bit annoying that they don't help an existing customer out! I can default boards for you if that helps. I had a board myself and the company that installed it locked out the NVM then promptly went bust. No point ripping out a perfectly good alarm eh! ;)
  12. B

    RCD with variable ms an mA settings

    Hi, been looking at variable RCDs as came across one at a job, settings range from 30mA to 3 Amps and ms from no delay to 3 second delay can someone explain please? As if I come to test my tester only goes up to 1000mA also some I’ve seen are set on like 0.5 seconds which isn’t an RCD meant to...
  13. hey-hey-my-my

    Multi-stage charging: skipping absorption?

    Good morning, I'm on the road year round in a motorhome with two 100w solar panels (soon to be doubled) charging a 260ah AGM battery via a 20a MPPT charge controller. I also hook up a 30a multi stage mains charger about once a week to properly charge the battery. I'd like to get the most out...
  14. Dan

    Google Ads have New Settings / Subscribed members new tools

    Okay, so this is part of a wider efforts to balance the books for the forums. We're trialing it out. But it comes with some good benefits as well as a few ads. So read the whole thread please before judging and replying. :) New Ads for logged-in users unless you have any one of the below:- You...
  15. Edtwozeronine

    Doogee screen keeps turning off despite settings

    This is my grandfather's doogee phone, not sure of the exact model - running some version of Android obviously... I did the usual and turned it off and on again, no luck! Screen goes to sleep mode or whatever they're calling it these days after what seems like 5 seconds of inactivity. It's set...
  16. Sms88

    Ir dome camera dip switch settings

    Hi. Just wondering if any one has experience with one of those ?
  17. Michael J

    Cordless screwdrivers with torque settings

    Can anybody recommend a good cordless screwdriver?
  18. B

    MCCB with RCD settings

    MCCB with RCD bolt on, anyone know how to work these settings out? Ignore settings now but this is upfront RCD TT system so I want to top one to be 0.3 for 300mA but unsure on bottom?
  19. Spoon

    Profile Settings.........

    Yes, this is probably a silly question... again. I want to stop receiving emails every time I get an Alert. I have gone into my Profile settings but I can't seem to find the tick box. The settings for my Alert Preferences look ok. I still want to receive them... Just want the emails to stop...
  20. Madocks

    Torque settings - hmm

    Bought a torque driver today, any clue on recomended values for connector blocks, henleys, MCB ? I imagine its cable size dependant? Anyone have a quick table i can print and laminate? Please dont say manufacturer instructions! would be poop!

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

Tags

advice aus cable circuit course earth electric electrical electrician hello led light lighting lights looking new please question rcd socket supply switch testing training wiring
This website was designed, optimised and is hosted by Untold Media. Operating under the name Untold Media since 2001.
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock