Hi,
I’m looking to install 3 meross smart switches for 3 lights:
entrance switch: only 1 gang but 3 way switch
bedroom switch: 2 gang (1 is 1 way, the other is the 3 way one)
living room switch: 2 gang (1 is 1 way, the other is the 3 way one)
I was planning to install 2 1 way MSS810 at the...
Looking for counsel / guidance to replace an original Dayton On/off with speed control switch. I’ve checked with a couple local electrical supply stores and no one could assist. This fan was installed in our attic 25+ years ago and difficult to access.
I would certainly prefer a simple, direct...
I have a bathroom fan with a moisture detector that turns it on and off. It also has a control circuit to turn it on/off when moisture is not connected. This is a no voltage/no current circuit.
I want to add a parallel control circuit that would of course be no load no current that I can turn...
I have a single wall switch powering 1 light and I want to add a separate light and change to wall switch to a double to power them both separel;y, how do i do this please?
Greetings.
I am new to this forum and I have a question regarding a relay that I am installing on a motorcycle wiring harness.
What I'm trying to do is install a momentary ignition switch, and the question is if the relay is connected correctly in this diagram.
Thanks in advance.
I'm installing smart modules in my light switches which means I need to replace the existing 25mm back boxes with 47mm ones. Downstairs all walls are brick and plaster so I've managed to deepen the back boxes with an SDS drill. I was expecting the same upstairs but some of the walls are lathe...
our dimmer switch stopped working after 7 years so went to replace it at the weekend. When I opened it up, the black wire was in the common slot and the red wire was in L1 which i thought odd because i thought it needed to be the other way around. Anyway as it had worked for so long that way...
Hi there,
Any advice on this would be greatly appreciated!
(Note, this is not a DIY, I'm using a fully qualified electrician, just posting here looking for advice)
We need a new fuse board fitted in a property I manage, which we hope to use for short term lets in the near future (Air BnB etc)...
Hi guys. I will start by apologizing for the elementary question. I'm sure you get them often.
The chandelier is in a hallway controlled by a switch. There is another light source in that same hallway but separately controlled by a pull chain bulb (still works). (in case it is important)...
A pull-cord shower switch is located in Zone 2 of a bathroom, including the ceiling base containing the electrical connections. With a little effort it may be possible to get spray from the shower onto the base.
I assume this is a C2, but wondered if anyone here might give it a C3, based on it...
Hi, I was ironing and lost power to the bedroom and bathroom. All outlets and lights. I checked the box and reset breakers still no power. I called out the guy who comes to do electrical "new home still under warranty " and he came in bedroom opened light switch, i took these pics. He did...
Hi,
I have a single light switch, wired like this.. the 2 wires in com, with a always live wire coming to the switch, and then wire going out to the light. (earth is in choc block at switch and light fixture)
I want to add a second switch like this
Does this look ok?
Thanks,
Derek.
Hi,
I've bought a "yagusmart" smart switch from Amazon and it has no earth terminal. Although there are no metal facing parts I would think the device itself still needs an earth? Or if not, where do I put the earth cable? It is a plastic back box with no earth terminal.
There is no indication...
Hello everyone...
There are a total of 4 cables entering the junction box at the top of the staircase.
Two 12/2 cables are coming in through the top of the box.
One 12/2 cable is coming through the bottom of the box, with a 12/3 cable coming through beside it.
The three 12/2 cables have...
I have a rocker type light switch the sticks out bit too far and interferes with a drawer, as in the picture. The switch seems properly installed, and I don't want to move it and the drawers are in a built in unit in a walk-in closet. As I need only about 1/4 more clearance, I wondered whether...
I'll start by saying - I have absolutely no intention of doing any wiring or anything electrical myself. You get someone professional to do a professional job - I know that. I just want to understand what I should consider so that I don't end up having to rip out or rework stuff afterwards.
The...
Hi everyone :) my first post here. Quick background I'm a newly qualified installer of somewhat advanced years whose just starting out in the trade.
The reason I'm posting is because I've been having a puzzling issue with Quinetic light switches, I can't seem to get any sense from Quinetic...
Hi everyone
I've moved into a flat and I've decided to replace the original electric switches and sockets with white ones. I've done them all however
I'm having problems getting the last 2 switches to work correctly:
There is a double light switch in the entrance hallway of my flat, the left...
Anyone know of a decent (and cheap) WIFI switch powered by 230V AC, but with isolated switch contacts?
I've used Sonoff BASIC R2 for a few things, but these only give a switched 230V output.
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.