tariff

  1. R

    Can I install an EMI filter to an existing solar system without jeopardising my feed in tariff?

    Can I install an RFI / EMI filter (designed to increase efficiency with a photvoltaic (PV) solar energy inverter) to an existing solar system without jeopardising my feed in tariff? https://www.eetimes.com/schaffner-emc-emi-filters-optimize-pv-solar-inverters/ Thanks
  2. mgrandy38

    do i need fused socket? economy 7 tariff

    Long story short im on economy 7 tariff but have 2 types of heaters in my house 1 convector fused socket, 3 storage heaters not fused sockets. So ive changed to tubular heaters (reduced from 2.5kw down to 270w) but the only one that seems to be running is the convector fused socket. Dang! does...
  3. S

    Solar Panels Can I add solar panels to an existing system without losing my fits

    Can I add solar panels to an existing system without jeopardising my feed in tariff? I have a 3.8kw system but was thinking of adding a few more. Could I have 6kw of solar but limit the inverter to 3.8kw so it will help in the winter when I need it the most. Or would I need a second meter to...
  4. I

    Advice needed on Immersion Heater moving from dual to single tariff supply

    Until last week I had a dual tariff electricity supply with a cheaper overnight tariff. This was good for the storage heating, but now the storage heaters are gone we've changed our electricity to a single electricity tariff. There are two consumer units with the off peak fuseboard supplying...
  5. R

    Solar Help setting up Export/Feed-in tariff after PV install

    Hi all I had my PV/Battery setup installed in May and since then all my excess PV is just fed back to the grid for free. When I initially tried to get setup on Octopus Energy they came back with this: "To correctly measure your export we have to get something called an export MPAN generated...
  6. HappyHippyDad

    Feed in tariff and exporting back to the grid - solar install question.

    I'm a little confused about whether I need to be MCS accredited or not. A few questions... 1. Can the customer still export back to the grid and get paid for this if I am not MCS? 2. Is there actually still any kind of FIT or smart export guarantee being offered anyway? 3. Plus, I'm not...
  7. Purvez

    UK How to set up multiple tariff sources?

    I want to do the following: There are 2 separate supply circuits in the flat. One is Normal tariff which is available all the time. The other is Economy 7 tariff which is only available between midnight and 7am. I want to wire a socket so that when Economy 7 is available it draws power...
  8. M

    Adapting CU for dual tariff, am i missing anything

    Hi all I've been ask to change another dual tarriff consumer unit (17 useable ways) I've changed a few of these in past but choice does seem limited and always seem to pay over the odds for what it is. I am considering adapting a dual rcd FuseBox consumer unit. I'm just checking am I missing...
  9. D

    How does variable electricity tariff work

    This might sound like a stupid question but if someone was on a variable electricity tariff and they didn't have a smart meter, and let's say the electricity was cheaper at night between 6pm to 11pm. How would the electricity provider know how much electricity you used at night so they could...
  10. J

    Anyone know where can get dual tariff DB suitable for this or possibly RCBO's

    Having trouble find a a dual tariff DB suitable for set up for this property. Can find a 5x5 way board but not suitable as have 7 ways on peak supply side. If not is there any RCBO's that are compatible for this board? Thanks 1600367772 See photo
  11. A

    Replacing a dual tariff supply consumer unit

    Afternoon all, I have been asked to change a consumer unit with a dual supply. I have a common supply, an off peak supply and one neutral, all 16mm double insulated tails. The current set up has the neutral running to the first isolator and then looping from there to the off peak isolator (2...
  12. W

    solar edge inverter and feed in tariff meter dont match

    Recently had fitted Solar Edge and notice their monitor gives a reading but the meter used to obtain my feed in tariff gives a lower figure and this is the one I am paid on not the solar edge inverter.So why the difference? this could cost a lot of money over the years.
  13. S

    Complicated dual tariff arrangement with four main switches.

    Hi Folks I'm used to (and understand reasonably well) simple dual tariff arrangements with two main switches (either two separate consumer units or a duplex). But I occasionally come across, and am now quoting for changing consumer units for a more complex arrangement that I don't full...
  14. Michael J

    Dual Tariff Supply where do you take the Ze

    Where do take the Ze on a dual tariff supply? At the 4 pole isolator (or do you change it to a circuit breaker)at the service head or in the consumer unit?If at the consumer unit which supply, the supply from isolator to consumer unit is a 16mm t&e. Your help will be greatly appreciated.
  15. W

    Getting rid of economy 7 tariff and Smart Meter

    Buying a house that has a mechanical meter with rotating dials that then branches into two modernish digital meters (not Smart), one for economy 7 and the other for the rest of the electrics. I only want a single tariff so if I have a Smart Meter fitted for free I assume they will take all three...
  16. C

    Dual Tariff or dual RCD

    Hello everyone I currently need to change a dual tariff (economy 7 & on peak) consumer unit situated inside a flat. One half of the existing split fuse board serves the storage heaters with the second separate half being the On peak supply. Am i correct in thinking a standard dual RCD board...
  17. LWS_Electrical

    Off peak tariff battery storage charging

    Customer has battery storage charged from solar panels and off peak supply. Should I be getting a 230v shock from the off peak cable when it's disconnected from the off peak DB? I would of thought there would be a diode to prevent 230v from the battery or solar panels from interacting with the...
  18. Colin188

    night tariff meter change to standard tariff

    I've been asked by a customer to remove four nights storage units and replace the switched fused spurs with single 13amp sockets. Each unit is fed from a dedicated consumer unit supplied from a economy 7 meter. I need to remove the meter tails from the night tariff meter and connect the consumer...
  19. S

    HMO conversion

    Hi Guys, After a bit of help in regards to sub main runs for some flats which are on dual tariff for storage heaters. Ive been asked to take this job over by the client and first fix has been done already. I admit I have limited experience when it comes to dual tariff supplies installed from...
  20. Midwest

    Economy 7 Installation

    I'm doing some work at a property that has off peak storage heaters & immersion heater. The old lady has just moved in, and are trying to understand how Economy 7 functions. None of my work involves the off peak supply. My understanding was that the only circuits to benefit from the off peak...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
This website was designed, optimised and is hosted by Untold Media. Operating under the name Untold Media since 2001.
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock