thermal

Recent contents Top users
  1. O

    wiring up a Gledhill thermal store

    I've always thought I was quite good a wiring heating systems, I can do Y plan, S plan, UFH set ups, "normal" thermal stores etc, you name it and I can do it and have done for years. However this system opened my eyes today, the thermal stores I have done in the past have had a coil that...
  2. B

    USB thermal camera for laptop

    Hello, I'm looking for an USB thermal camera to connect it and stream the image to my laptop. Most of the products I've seen on the Internet are made for smartphones (USB C/Apple Lightning) and I'm not sure If they would work connected to a laptop using an USB A male to USB C female adapter for...
  3. E

    MIRA Shower Thermal Cut Out

    I replaced the Thermal cut out on the shower and all's good then 3 days later I receive a call that its only pushing out cold water again, any thoughts what's causing the operation of the cut out, the water pressure is good
  4. bigspark17

    Solar i boost taking out thermal cutout

    Hi all. Has anybody experience solar iboost creating problems with immersion heater safety cut out? Does the iboost somehow heat the tank higher than the thermostat or does it have something to do with the iboost heating via DC.
  5. H

    Thermal print head for a parking management system based on Raspberry Pi pico and HMI

    Materials to be used 1、STONE STWI101WT-01 2、FTP thermal printer head 3、Raspberry Pi pico 4、Coin-operated machine Function The control function is displayed on the serial screen, the main interface selects the floor, after entering the main interface selects the parking space, at the same...
  6. A

    High power manually-reset thermal cutout solution

    Hi I am trying to create a thermal cutout circuit to protect a large (10sqm) silicone heat pad table. The total heat pad load is around 30A (split between seven 1kW heat pads), running off a single phase 32A supply. The heaters are controlled with Eurotherms and SSRs, which fail in the closed...
  7. S

    Hot Tub Thermal Cut Out (Over Temperature) Cleverspa

    Hi, The heater over temp protection (bi-metal) switch on my Cleverspa has failed open circuit. If I link it out, the heater still works. As expected, the manufacturer hasn't replied. So, can anybody advise the type / part number if this part; or advise the temperature at which this over-temp...
  8. J

    Thermal Camera Advice Please

    Hi Looking at getting a basic thermal imagining camera to look for tell tale hot spots on electrical equipment. Anyone know of a better one for the money than this please: -...
  9. J

    Is the 2 cables in the connector blocks the thermal OL

  10. Zdb

    For Sale [FLIR] Cat S60 Thermal camera

    Hi guys. I'm selling a Cat S60 rugged smartphone with an integrated Flir thermal camera. The phone/thermal camera is in excellent condition and comes with a charger and protective case. The box is missing (probably in the loft somewhere). This is a great starter camera for anyone looking to...
  11. K

    Running 16mm CU feed in ceiling with thermal over 100mm

    Hi I have to run a feed to a CU in the middle of a ground floor flat . Its already got 2 layers of blue board and 100mm rockwool above it . It would be clipped in the ceiling over 50mm above the ceiling height . rockwool in the jist space and 2 layers of pink board below . So method 101 ...
  12. P

    planning to instal solar thermal for solar heat air

    I am planning to instal solar thermal for solar heat air. Do not know which service provider is best? Can anyone look into this website and give suggestions regarding whether I can use their service or not. Home - Clean Energy Ireland- Renewable Energy Solutions | Solar PV Panels | Ventilation |...
  13. B

    Tying in Gas Insert power to Gas Boiler Thermal Shutoff

    Hello, Getting a Gas Insert for fireplace. I was going to pull power from outlet in basement. Plumber told me that typically electricians tie into existing thermal cutoff for gas boiler. Seems reasonable, but not sure how to tie in? Should I tie in before and after thermal cutoff?
  14. Q

    Reference methods for cables ran under floorboards and into stud walls no thermal insulation

    evening all I am wondering what the installation methods should be for cables run under floor boards and then into stud walls but without thermal insulation...102,103 dont seem relevant and so my understanding leads me to think it would be a cross between c for clipped direct under the boards...
  15. G

    UK T&E thermal effects/derating

    Hi everyone. I'm about to start the wiring of an extension to my house which includes a new kitchen and bedroom. I am an electrician that mainly works in industrial settings but have done domestic work on and off over the years. It's been a while since I've done any new build installs like my...
  16. J

    Thermal overload

    Got a 7.5kw pump that’s blocked. Overload set to full load current of 13amp and fuses are BS88-2 20M25 but it keeps blowing the main fuses every time it’s blocked why would this be. The motor electrical is fine tested insulation resistance and resistance of winding. Thanks for your help in advance.
  17. Q

    Reference methods for cavity walls without thermal insulation

    Evening all Just wondering what would be the reference method given for a twin and earth cable in a cavity wall without insulation....I understand with insulation its either 102 or 103 but these massively de rate a cable and so was thinking is it b without the insulation as it acts similar to...
  18. J

    Thermal overload

    Can a thermal overload protect against fire?
  19. C

    Opinion On Cable Ampacity in Thermal Insulation

    Ok, so a while back I came across a rather interesting article referencing an incident where MC cable had been buried in thermal insulation resulting in a small fire. The magazine claims that if the cable was de-rated to BS7671 standards over heating would not have occurred. However, I am...
  20. O

    UK Thermal breaker to derate circuit?

    Hi chaps and chapettes, I have a buried 6mm SWA 32a radial circuit powering a single 32a commando/ceeform, i'm looking to add a 16a ceeform for convenience. Can I use a thermal-magnetic breaker to derate to 16a. There isn't space for a 2 way CU so would this be my best option? Thanks.

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

Tags

advice aus cable circuit course earth electric electrical electrician hello led light lighting lights looking new please question rcd socket supply switch testing training wiring
This website was designed, optimised and is hosted by Untold Media. Operating under the name Untold Media since 2001.
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock