Is anyone aware of any galv trunking that is smaller than 50x50. I'm drawing a blank online.
I've taken over a job that's used 16mm twin and earth (along with separate 16mm CPC) as a distribution circuit.
While I can arrange for most of it to be clipped direct, there's about 4m that is going to...
Hi, I am currently doing a level 2 (2365). We have been doing trunking factors and I am not sure about if you need to apply the 45% space regulation to the factor. For example, if I have trunking of 50 mm x 50 mm the trunking factor is 767. I have 1.5 mm solid thermosetting cables that have a...
Hi all.
I am installing some metal trunking vertically in a meter cupboard to contain all the meter tails for an apartment block. I have 5 sets of tails entering one “row” of meters, and about 300mm further down the trunking I have another 4 sets of tails entering the other row of meters. Due...
I have checked the regs and can't find anything to say this can't be done. Although I'm worried about cable movement in the case of short circuit damaging singles in the trunking
Morning,
Company had an external contractor coming in to complete an EICR recently. They have gave us the report with a C2 for holes in trunking at high level. For reference, this trunking has been pre-drilled with 20mm holes at set distances on either side. Within this trunking is multiple...
Hi Everyone,
Sorry if this is a silly question. I am supporting my mum with some small home renovations, in preparation for a care home. I am trying to do what I can myself to help her with costs.
Can I ask if cables that have been run around the ceiling of a kitchen within dated trunking, is...
Is it acceptable to run mini trunking as shown in the pic? To my mind it would be safer (and slightly less ugly) to have a drop from each socket and then run it along the top of the skirting. I would be concerned about the trunking coming loose and being more likely to suffer mechanical...
Hi guys,
Looking to see if anyone has one of these legrande/Salamandre jig markers lying around. Mine seems to have gone walkabouts. They were free a while back but I’m happy to pay for one if anyone has one spare. Don’t think they do them anymore and I’ve looked everywhere.
Thank you
I’m looking for an alternative for hacksaw for my yt4. I seen a guy on site using some sort of pipe slice, but for trunking never got the chance to ask him. Any ideas? Seen the ratchet cutters but not for this size trunking or should I just stick to the trusty hacksaw
Spent a good hour tonight fighting crappy 38x25mm trunking - surely it can't all be this badly made?!
My fault for getting it from Screwfix so that it came in 2m lengths, I guess. (Tower brand).
I've not had issues with their smaller trunking before, but this stuff was a nightmare. Felt fairly...
Hi, would anyone be able to recommend what kind of trunking i should use from a consumer unit down to floor level as the cables come from under the floor up along the surface of the wall into the back of the consumer, i am currently working on a board change in a domestic where all the cables...
Does the consumer units top knockouts need to have stuffing glands installed even if a 50x50 trunking will cover the holes? Or is it sufficient to use a grommet or grommet strip if a rectangular hole is cut?
The stuffing gland will maintain the IP rating but that will be maintained by the...
I have bought a Mini Mitre Block for some Trunking as the cutters I have are better for Mini Trunking. I’m just looking for something that will allow me to mark the angle before cutting it. I was thinking either a Tri-Square or Trend ANGLEFIX. I then also need some advice on a file to smooth the...
I'm a bit out of touch re 18th edition.
Is it really necessary to fit loads of additional metal saddles inside trunking when it's only 400mm above the concrete ground floor of a sports hall?
All the stuff about premature collapse makes sense, but where, in this case, if the cable going to...
It's not that often I stare stupidly at something for 5 minutes and can't work out where to start, but....
The horizontal and lower vertical trunking aren't actually connected together or bonded. The upper vertical is cable tied to some SWA and flaps in the wind.
Singles are nicely tensioned...
In an industrial building with galvanised trunking everywhere and loads of circuits with singles, has anyone got any good tips on identifying the singles for a circuit easily if I needed to break into a ring for example?
I need to install an additional consumer unit. Normally I would put the existing tails into Henley blocks and feed both CU from there, but in this case there is an isolation switch, and the output tails are in metal trunking from the isolator to the CU. The new CU is going next to the old one on...
Hi.
I am planing on building a (not sure what to call it) U shaped storage solution which goes either side and above the headboard of a bed. I want to install a couple of reading lights either side.
A mixture of me not being bothered and running out of money means I cant run cable on the...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.