workshop

Recent contents Top users
  1. O

    Wiring in log cabin workshop

    Hi all, I have a log cabin in my garden. An electrician ran an armoured cable from my consumer unit to the log cabin and this terminates on the outside in an exterior junction box. From there, there is a single circuit in the cabin that supplies two external security lights plus power sockets...
  2. PezLee

    Workshop keyed safety

    I would like to convert my detached garage into a full time workshop, storm-time garage. As I have a 7 year old (and JUST found out another on the way :) ), I would like to add a keyed switch that will disable several circuits dedicated to tools when my wife or I are not using them (preferably...
  3. M

    E-stops for Car Workshop Ramps

    Hi guys, A car showroom / workshop brand we do work for has asked us to modify a few things in the workshop. One of them being to implement emergency stops into the ramp controls. Getting involved with modifying the ramp control box is something I'd rather avoid as it was obviously wired up...
  4. Tim pan

    Metal workshop in shipping container

    Some friends are setting up a metal workshop inside a shipping container, on site at a commercial building that rents out studios, workshop space etc. There is a 16mm SWA providing a three phase supply to a board inside the container, I looked and it’s connected inside the main building to a...
  5. D

    Future Proofing - Garden Workshop

    Hi all, Im a recent home owner, and have a long term plan to build a workshop/office at the back of the garden (about 20 meters long garden). Consumer unit is at front of house and an awkward position so routing the cable internally will be almost impossible once everything is decorated. The...
  6. N

    Power to workshop from home

    Looking for a little help please... running power to workshop. My home has a 200amp service. Neutral and ground are bonded at meter on outside of home. Main breaker box in house has neutral(white) and ground separated. I have a 100amp breaker installed in the main panel which ran to a sub panel...
  7. P

    LED suggestions for a workshop

    Good morning all, staying warm I hope We are just moving into a new workshop and would like to change the current lighting to LED, currently there is sodium lights giving out an orange light which in not very eye friendly for our type of work so we are looking for advice or recommendations for...
  8. S

    Problem with the mains in my workshop

    Hi. I've just started renovating my workshop. It's about 30 years old, the walls on the inside have been doubled up with 15mm plasterboard. My plan is to cover the walls with 6mm hardwood ply because I got the sheets for free. I've just started screwing them to the walls. The original...
  9. G

    I need advice on rewiring my workshop.

    I need advice on whether or not I can use the original wires that bring power into my detached structure. The photos show the exterior connection from the power lines that would have a dial from the power company when active. It's currently not active. Another photo shows the exterior wiring...
  10. C

    Workshop power

    Hello can anyone offer and advice on running power to an workshop. All work will be done by a professional electrician, I am merely seeing if my idea is feasible. So far I have 6mm swa prysmian cable buried according to reg, sand bedded and warning tape over etc 6.5 metre run. I have recently...
  11. mattg4321

    GSM CCTV for workshop

    Hi guys Can someone recommend a decent cctv system for a customers workshop. Lots of expensive gear in there and he’d like to keep an eye on it. Have power easily available, but no Wi-fi/internet connection. All the 4G/GSM units I’ve seen seem to be battery only which would be annoying to...
  12. L

    Second CU in domestic workshop - some advice please?

    Hello, If I wanted to put a second Consumer Unit in a domestic workshop with the following criteria, what cable would you advise for the extension. Remote CU would be 50m away from the main board. The main board is not in a house but a separate garage, is a dedicated supply and has it's own...
  13. Mark42

    'Leapfrog' wiring of a ring in a long workshop. What do you think?

    I'm insulating, and replacing the wiring, in one of my own (metal, agricultural-type) workshops - fitting 13A/16A sockets on each of the horizontal 'top hat' wall rails, 20m long, with each 4m bay having 4-5 sockets. This will be done in stages over the next year: the insulation and...
  14. J

    Does workshop equipment such as lathes require RCD protection.

    Does workshop equipment such as lathes and mills Need rcd protection?
  15. S

    Workshop Q light gauge 220v can a 3 phase 415v connection be made up?

    Hello again and Happy NY all. I have decided to take a small piece of family land and erect a house ( live for a few years) As part of this, i have to do a lot myself, joinery carpentry etc. I have access to a rural farm workshop to conduct all, its dry but the electrical connection is run...
  16. S

    Workshop Lighting

    I am trying to find the most cost effective way of lighting a woodwork shop which is in an old building, 5m wide and 30 m long and could have up to 20 men in there. It has a pitched roof about 4m at the peak and 2m at the walls. I was advised to use LED low bay lights and bought a 200w flying...
  17. robertl

    UK 480v Split Phase, new workshop, VFD's required

    Hi All, I've posted on here before about this, that time i was asking what people thought about phase converters as at that point i thought i could only get a single phase line at 100a for my new workshop. Turns out that after the DNO visited the site i can get a Split Phase connection put in...
  18. T

    UK New Lathe in the Workshop

    Over the summer we had some single phase workshop gear removed, and in it's place was delivered a second-hand 3-phase lathe. At first I was going to drop in a new circuit, as naturally, the single-phase circuit that exists is useless. However, this new lathe is going right next to another lathe...
  19. robertl

    Single phase power all thats avaiable for new workshop build

    Hello Everyone, new to the forum and looking for some advice on a new workshop, i'll explain. I am planning on building a metal / woodworking workshop (mainly aluminium and stainless steel) for boat work, refurbishment and boat building. I am a marine engineer to trade and i am planning on...
  20. A032701

    options for workshop supply

    just wondering what people would think would be the best way of doing this. i have got to provide a supply up to a workshop in a garden (about 80 mtrs from the house). it will run underground all the way and then in the subfloor of the house that is currently being worked on all the way to the db.

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

Tags

advice aus cable circuit course earth electric electrical electrician hello led light lighting lights looking new please question rcd socket supply switch testing training wiring
This website was designed, optimised and is hosted by Untold Media. Operating under the name Untold Media since 2001.
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock