between

  1. W

    Testing voltage between ignition and solenoid

    I'm trying to test if there's voltage between my ignition and the solenoid. The starter won't crank or click so figured I'd start here but am not sure if I'm doing this correctly. I have a male/female connector from the ignition to the solenoid. I disconnected this, connected a probe to the...
  2. Spoon

    Minimum distance between electrical enclosures

    Hi people, I'm having a brain fart moment. What is the minimum distance between enclosures, with doors that are facing each other? In EN60204-1:2006+A1:2009 section 11.5 said " In the case where such parts are present on both sides on the access way, the clear width shall be at least 1.5 m."...
  3. W

    Difference in scrap price between pvc insulated twin & stripped cable.

    I’ve got a hell of a lot of scrap cable in my garage. I know it would take a long time but is it financially beneficial to strip the cable or does it not make much difference?
  4. dokkan1080

    Continuity between lives

    I think i might of asked this before but Here goes again, on my flat cu with the mcbs off if I use my voltage tester between a lighting circuit and socket radial I get continuity? Why is that? But of I power up one mcb the others don't get powered up.
  5. N

    rewire choosing between 2 unregistered firms to do the job

    Hello thanks for reading - I am having a 3 bed semi rewired and narrowed it down to 2 electricians. Both a not on any register as far as I can see. One will do the work in 3 days (3 people doing long days) and get it signed off under the Third Party Certification scheme The other says he...
  6. E

    Can I use H-Tap Compression connectors between main and sub panels?

    Hello all, I am new to this forum and had a question about installing a new panel. The previous owner had installed an Aluminum 3/0 2 AWG cable from main panel to the garage. I would like to install a 100 amp panel in my garage to add additional circuits for my house to install near my garage...
  7. C

    USA Difference between Eaton's residential & commercial duplex receptacles?

    I am having trouble determining the significant differences between Eaton's residential & commercial duplex receptacles: Model #270W-10-LW (https://www.lowes.com/pd/Eaton-White-15-Amp-Duplex-Outlet-Residential-10-Pack-Outlet/1001438408) Model #BR15W-10-LW...
  8. dokkan1080

    Continuity between live conductors

    On my cu at home I have a continuity reading between my ring final circuit and a radial circuit of 114ohms between live conductors. When I test continuity from each breaker. Why would that be? Break down of cable If I turn one off and leave the other on I don't get a voltage. At what point...
  9. S

    T&E between light switches, what are my options?

    Hey, my downstairs hallway light switch is a 2 gang but doesn't control my upstairs hallway light (and just a 1 way for the upstairs light). After inspecting, there is unconnected T&E thats runs to the upstairs light from the downstairs 2 gang switch. Now I know that can't be used as a 3 core...
  10. B

    What is the difference between the LCL and C&G Part P qualification?

    hi studying for Part P and the exam board from my course is LCL, is this a problem?
  11. E

    Jumper between two different receptacles.

    I am finishing my basement. Come across something I didn't see before. I have two different receptacles in my basement and each one has its own breaker at the breaker box. And there is cable running between these two receptacles. I would love to learn why there is a cable running between these...
  12. J

    UK Continuity Between Line and Earth

    Just tested the end to end resistance on a ring main at a socket outlet. Readings are spot on however when changing the crocodile clips I notice that I have around 600ohms of resistance between the Line and Earth conductors. The system is TT. What could be the cause of this?
  13. K

    180v between live/neutral but 240 between live/earth

    Hi all Downstairs lighting circuit isn’t working so tested voltage at each fitting and getting 180 live-neutral and 240 live-earth. Have checked continuity from board to each fitting and got a neutral all the way around the circuit so I’m a bit stumped on what the issue can be. There is access...
  14. Abbywho

    Anyone know the difference between a red and green wire, besides the fact that red is more dangerous?

    Does anyone know the differences between a ref and green wire?
  15. K

    UK Voltage between gas bond to neutral

    So up until this morning I thought I had seen most faults in an electrical installation, but this one today has me stumped and I’m not sure if I’m being stupid and the issue is staring me right in the face! long story short we went to a domestic property with a TNCS to install a supply to a...
  16. A

    Are LED bulbs better than CLF bulbs?

    Recently, I have decided to switch to LED lighting instead of any other old school lighting. Our government has taken the initiative of replacing old lights with energy-efficient LED bulbs. But there is still a debate about which lighting option is better, is it LED or CLF. Give me your...
  17. HappyHippyDad

    Understanding the relationship between TNCS, TNS and TT

    I have never actually had to make an electrical system into a TT. I have added rods in order to get an effective Ra but never had to (for example) install a TT on a new garage or shed. It's best I give an example with regards my question.. A new garage has a supply taken to it from the house...
  18. S

    Difference between dead short and short circuit

    Hi looking for some help about faults and symptoms and difference between short circuit, dead short, and overcurrent to know which fault you have. Is short circuit line and and neutral fault dead short zero resistance and a tripped breaker And overcurrent to much current in circuit causing...
  19. A

    Difference between Dimplex Quantum models

    Hi all, I’ve got a question about the Dimplex Quantum High Heat Retention Storage Heaters. I’ve been in discussion with a supplier about these. He’s provided a few quotes. He’s knocked about £350 off the price by offering my the G series Quantums. He says these are exactly the same as the RF...
  20. M

    What should be the minimum resistance required between 3 phase and grounding (connecting wire to earth)

    Hi I am new to electrical engineering. I want to measure the 3 phase voltage near the water pumpset motors. I have connected phase lines to earth through a diode and six 1 mega ohm resistors (measuring the voltage across resistor). The same earthing wire is connected to ground in my dc circuit...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
This website was designed, optimised and is hosted by Untold Media. Operating under the name Untold Media since 2001.
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock