board

Board International S.A. is a Business Intelligence (BI) and Corporate Performance Management (CPM) software vendor known for its Board tool kit. The company was based in Chiasso, Switzerland, where it was founded in 1994, and Boston, Massachusetts.Board International now operates in 19 countries, with around 3,000 customers from a number of variety of industries,

View More On Wikipedia.org
  1. Anthony Deakin

    Light Sensor Trips Fuse board

    Hi all, I am trying to work out why an outside light PIR trips the light in turn trips the whole fuse board inside the house.. When the PIR is disconnected then everything works fine. Anyone come across this before? There is no moisture, all wires connected and ip66 Thank You
  2. D

    Can One Electrical Meter Box Feed a Second Board?

    Hello everyone, I hope you are all doing well in these trying times. I'm planning an extension to my house, and I'm looking to have a second consumer board fitted inside the extension. I'm hoping I can feed this new board from the meter box and not as a sub-board from the original consumer unit...
  3. L

    Discrimination to sub board

    Sorry if this is obvious but I thought discrimination was for down stream? I want to feed and outdoor unit which only requires 6am and 16amp, it has a little sub board with these breakers but a 100a main switch, my supply is a 32a commando outlet. Should I feed existing sub board with existing...
  4. M

    UK After 3phase board, ideally some board wiring/testing too - LONDON/SE

    I'm a mechanical manager with some electrical background (2330 L2 from college, 18th ed, 2392). About to be an M+E manager so need to brush up on areas I'm unfamiliar with - 3 phase wiring and testing is the big one. Is there anyone in London area with access to a (used) 3phase board who can...
  5. H

    Can I take a switchwire back to the board ?

    Just a question I’ve always been taught no but some of the older guys say yes and newer guys say no and just wondering if anyone has a clear answer for me ?
  6. N

    When working on circuits do you isolate whole board or just the final circuits using MCBs ?

    When working on circuits do you isolate whole board or just the final circuits using MCBs ? Or is there any instances when the whole board has to be isolated even if you are working on few final circuits? Thanks.
  7. W

    Reversed Tails at Board

    Apart from swapping them over, what would you do if you came across Live & Neutral tails reversed at the consumer unit?
  8. Dave Appleby

    Board size

    Anyone know any low height boards? I only have 19cm height available. Only needs to be 10 way. Bit stumped! TIA Dave
  9. L

    Modification of 3 phase board

    Hello, wanting to install a new (old) MCCB in an Dorman Smith Loadline board, found a couple online, however, the client ordering the works is not keen on installing old breakers, so they would rather us connect tails onto the busbar stubs where the breaker would usually be, fashion some kind of...
  10. D

    Customer actually starts sticking his hands inside a live board while chatting to Delroy

    https://www.electriciansforums.net/media/dont-touch-that-hands-on-customer-attempts-insanely-dangerous-diy.19349/ Scroll to about 4.30 minute mark , I honest don’t think I have ever had a custOmer physically stick their hand inside the consumer unit while I’m trying to work delroy Gets all the...
  11. T

    Extending cables for a new board change

    Hi all, looking for some advice with regards to extending cables for a consumer unit change. The old board is a mess inside with cables being cut short etc. What's your go to method for extending. When I've only had to extend a couple I've used the Ideal inline splice connectors, but this is...
  12. Dave OCD

    Todays board change - 'real world' with older cables.

    This was commenced at 2.30pm today after having to locate and rectify an open neutral on a ring, missing earth continuity on a lighting circuit and 2 sockets spurred off the cooker. ? It's as good as I could make it with the older T&Es , and annoying that everything barring 2 lives of a ring...
  13. M

    Australia Adding a portable petrol backup generator to the main switch board.

    Hi, I want to add a change over switch so that a portable backup petrol generator can be used when grid power goes down. As it has in Victoria. On referring to AS/NZS 3010:2017 to connect a portable generator. Figure 4.3 on page 57 shows a 1 pole Circuit Breaker in the active wire between the...
  14. HappyHippyDad

    Will an RCBO fit in the MK board?

    I want to change the 3 MCB's in the picture for RCBO's. Will the MK ones fit? Cheers ?
  15. HappyHippyDad

    Which RCBO fits this merlin gerlin multi 9 board?

    The board in the picture below has 2 x RCBO's in it, they look like matches so I'm guessing schneider is the new merlin gerlin and that these RCBO's are a perfect fit? However, Schneider seem to do other RCBO's. Easy9, acti9 and others. The Acti9 looks like it may fit this board but it is more...
  16. D

    Board change on 16mm tails

    Hello all Just some input needed I have 16mm meter tails & earth looks undersized coming unto the board also. I want the consumer unit changed, I understand that the tails need to be 25mm & earth 10mm I spoke with my electricity supplier who is going to get the technical department to call...
  17. R

    Australia Where to buy 120mm wall clip for fitting electric switch board

    I want to replace my current 6 gang switch board with a glass panel switch board. Bought it online. But when I got the board I realised it's bigger than my current board and it won't fit in the current hole. I can make a bigger hole but the current clip won't fit either. I tried Bunning they...
  18. R

    What Crabtree type RCBO fits this board?

    Hello guys, completely forgot to remove the board cover to check what type of rcbo was required for this particular Crabtree board. Anyone from experience know which type RCBO fits? thanks in advance!!
  19. A

    What gauge cable from meter to fuse board??

    Hi, I just had a new 18th gen with surge protection installed. They disconnected the old cable and did a new run, the cert says 10 gauge was used but then I just had a different sparky who is looking to wire up my garage see it and say it should be 16. Just wondering what is correct and should...
  20. Pretty Mouth

    Bungalow board change

    Have had an estimate accepted for a CU change in a 1980s bungalow. I based the estimate mainly on an EICR which was carried out on the property by another spark last summer, plus I had a quick look at the existing board, meter, and bonding. The EICR has all circuits listed as ref method C...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
This website was designed, optimised and is hosted by Untold Media. Operating under the name Untold Media since 2001.
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock