Posting a message to the forum will remove the above advertisement

connected

Page 1 of 9

Recent Content Tagged With connected

Thread
Motor Tripping RCD but it's not even connected to it

Hi, I have just installed a dedicated 32A circuit to feed a motor which according to the data plate is 3.0kW and 16.6 Amps, single phase. It is...

Thread by: JD Hogg, Oct 5, 2017, 57 replies, in forum: Electrical Forum
Thread
Question regarding 400V three phase lighting connected in Delta, without Neutral.

I am in the process of designing the electrical installation of a community centre, and have a question about the provision of three phase...

Thread by: AReynolds, Jul 29, 2017, 39 replies, in forum: Commercial Electrical Talk
Thread
Two cables connected to mcb

Evening All Im sure this will have been discussed at some point (if so please point me to a relevant thread) I have been to look at some...

Thread by: Jay89, Jul 11, 2017, 94 replies, in forum: Electrical Forum
Thread
Are you best electrician??

We're launching our first Smart Solution awards and want to celebrate contractors and installers who are working with Smart Technology. If you're...

Thread by: Voltimum UK, Jun 5, 2017, 3 replies, in forum: Electrical Forum
Thread
Main gas bond connected in the wrong place

hello guys I need some advice on and EICR job. On the MET we have two main bonding conductors 10mm each. Water is fine however I cannot find the...

Thread by: chris day, Apr 22, 2017, 10 replies, in forum: Electrical Wiring, Theories and Regulations
Thread
Invertor Error - FE Not Connected

Hi guys. So, we've had solar panels installed on the roof for about 3 years now, and just recently, had an issue where the Invertor in the loft...

Thread by: lovelldr, Apr 13, 2017, 10 replies, in forum: Solar PV Forum
Thread
Strange earthing arrangement.

Hello all. Had a job today putting in a new kitchen circuit. Plan was to put in a new CU just for the kitchen sockets and lights. When I looked...

Thread by: Bobble23, Mar 16, 2017, 4 replies, in forum: Electrical Forum
Thread
500v Insulation Resistance Test ok?

Hi all, still training so please forgive my very simple question. Why is it ok to test an appliance at 500vdc when PAT testing but great care...

Thread by: shinypen, Mar 11, 2017, 4 replies, in forum: PAT Testing Forum
Thread
Neutral bar

i couldn't find the answer to, Why is the neutral bar not live in simple terms. Im thinking Line from mcb to equipment then neutral connected from...

Thread by: Wilson12, Mar 3, 2017, 7 replies, in forum: Electrical Courses & Electrical NVQ's
Thread
Replace shower pull switch

Hello Guy's I replace shower pull cord switch like same last one but there before not conecte earth wire I done like that before wire connect with...

Thread by: Badri nath Paudel, Feb 17, 2017, 33 replies, in forum: New Member Introductions
Thread
Inverter on earth stake?

Been asked to replace an old consumer unit, PV installed so bonding etc up to scratch. House supply is TNCS, however with the PV wiring the...

Thread by: yellowvanman, Feb 14, 2017, 4 replies, in forum: Solar PV Forum
Thread
Submain Earth/Bonding question?

Hi guys/girls Just some clarification needed. I have an house where there is sub board in the garage , and also a boiler in the garage. The water...

Thread by: Flakey, Feb 7, 2017, 24 replies, in forum: Electrical Forum
Thread
Export Limitation

I received a call from a person who was not a customer of mine asking to connect up his 8 kW PV system. Its a new build and the modules were...

Thread by: Stuart Houghton, Jan 30, 2017, 3 replies, in forum: Solar PV Forum
Thread
Insulation Resistance test with 12v transformers

I am installing a C/U and the kitchen has some old Down lights installed with 10 x 12 volt transformers connected. I know I could disconnect all...

Thread by: Nicebloke, Jan 28, 2017, 3 replies, in forum: Electrical Forum
Thread
Supplementary bonding question

hi all, I know there are many questions on this topic but I'm unable to find my answer. Can I connect my 4mm supplementary bonding cable to the...

Thread by: Leader, Jan 16, 2017, 18 replies, in forum: Electrical Wiring, Theories and Regulations
Thread
low IR

hi did a IR on a shed board L-N was 0.11Mohms so took out the radial circiut and light circuit did them separately and was fine 299Mohms so why...

Thread by: terry1969, Jan 15, 2017, 33 replies, in forum: Electrical Forum
Thread
Generator earth

Hi all, first post for some time! Currently installing power and lighting into a small cabin. Supply will be from a permanently connected...

Thread by: Sparkystu79, Jan 11, 2017, 8 replies, in forum: Electrical Forum
Thread
13A Oven Install Query

Hi, I have just purchased a new oven which is 13A. The old oven was connected to a MK 45A DP Cooker Control Unit with Neon. Can I just connect...

Thread by: AnonzI, Jan 4, 2017, 1 replies, in forum: New Member Introductions
Thread
Ring main tripped struggling to find cause

32amp ring main tripped mcb and rcd overnight. Rcd will reset but not all the time, mcb will not reset. Unplugged everything in house and mcb...

Thread by: Paddington, Dec 6, 2016, 10 replies, in forum: Electrical Forum
Thread
EICR question

Hi chaps, This may have been asked before but i cant seem to find it when searching so im sorry if someone easily finds it. Im currently...

Thread by: akwoody2, Nov 28, 2016, 28 replies, in forum: Electrical Forum

Showing results 1 to 20 of 169

Page 1 of 9

- Contest Winner JOTM Competition- September 2017 posted by Dan. JOTM Competition- September 2017 Winners (12 Likes) [IMG]@Plan Tec Tiling (Wet... Contest Winner JOTM Competition- September 2017
- tiling directly on to brick work question posted by what. Is there any reason why you cant tile directly onto brickwork if you use plenty of good adhesive? I have a shallow brick fireplace recess which i am preparing for a wood burning stove It...
- Advice how to deal with non paying customer posted by Gnrbytile. Hi, I am after some honest advice regarding a job I done a few weeks ago for which I haven't been paid for. I laid kitchen floor and wall splashback for client who had just had new kitchen......
- Heating Bangs when switching off. posted by Paul Cooksn. Hi, I have an older style open vented heating system with a Glow worm 50/60 RF flued fan boiler. I have a hot water tank on the first floor and two header tanks in the loft, one large for the hot...
- Combi boiler installation posted by Sonia Muss. We've just had a new combi boiler installed by a corgi registered engineer and there's a join with 2 different size pipes as picture. We were told by other engineered when getting quotes that the...
- Alton Hampshire losing pressure & patience posted by John Merrix. Sealed ch system loses pressure daily and we can’t find any leaks, this has recently been installed the were several leaks initially that have been rectified but still losing pressure . We have...

Electricians Directory Post a Domestic Job Post a Commercial Job