Hoping to get some advice as i like to understand what work will be carried out and what actually needs doing etc.
Looking at replacing the hob & oven as they are on their way out and in my research I've found out the following.
Oven & hob are both connected to an isolating switch just above...
2 Questions,
1. 2.5mm T+E on radial, 20A breaker feeding 1 FCU that feeds water heater, can I come off this FCU with another FCU to feed a heater?
2. 2.5mm ring main, consisting off FCU and sockets all on ring, can I come off one of these FCU to feed a FCU spur?
Hi,
In the past, my flat had 2 beepers , 1 at the door, and 1 at the study much further away. In recent years, the evil housing association which owns the building has introduced new beepers/buzzers, but this time only 1 for each flat. Now, I find that, with just 1 buzzer/beeper, I cannot hear...
Hi All,
I have a wundafloor 3 zone uf heating system and a separate rad system running off a Baxi Ecoblue Advance heat Boiler and Megaflo tank. The rad system runs fine via a Danfoss controller but the installer has not wired the uf controller to the boiler so the uf cannot "call" for heat and...
Asked to connect a cooker up today, it is to an existing install, removed temporarily to allow new base units to be fitted.
Connected it back up. however it was connected direct to isolator switch. no connection plate on the wall. cable comes down in wall, then out behind cupboard and then...
Hi all. Shower has melted on top left corner. I thought it would likely be a loose connections on the feed. On taking the cover off the 10mm coming in and connector block looks fine and is tight and I soon realised the burn Mark is from the live going from the block up to the top of the...
I am in the process of buying a new
Bosch Serie 4 HBS534BS0B.
Total connected load electric: 2.99 KW. AO who I am buying it from state that it can be connected to a 13A socket other seller are saying it is 13 Amp (Requires hardwiring to a fused spur).
There is a 13A socket already there that...
gas engineer can't fit new heating programmer as I need a neutral connection on the back plate. Advised to get an electrician. How much would this cost or would it be better getting a new heating system?
The neon light on my flat-plate/switched fused connection unit doesn't come on when I use the washing machine. The machine still works - but does the fact that the light doesn't come on mean something is wrong? Do I need to get an electrician in?
Howdy - first post and need some advice. Baxi 630 boiler
To start with i am not qualified in anything and i know the wiring in the photo is from the 90s. Please bear with me....
We had a new boiler fitted a couple of weeks ago by a certified gas engineer. He was a sub of my builder. At the...
Just a quick questiin can i use a 3 amp for a 2A fused connection unit the factory manuel is saying 2 amp full stop is this 100% or can i use a 3 amp i would of thought this would be sufficiant and then wired to a 6 amp breaker? Never done a alarm system before so making sure as dont want to pop...
Hi all,
A client has kindly changed their mind on the emergency light they are using. They want to me to install these
https://www.channelsafety.co.uk/emergency-lighting/all-led-downlight-products/glade-1w-led-downlight/
I’ve used these quite a lot and I’m most casss they are a good job, I...
Today I found a free standing cooker connected with T&E cable. Since the cooker is bordered by cupboards it is regularly pulled forward about a metre for cleaning the unit and the floor beneath it.
This forward movement extends the cable to full stretch while pushing it back makes it hang in a...
I'm building a seven type car and using a Mitsubishi Galant steering column with light stalk and ignition switch. Lights indicators are all sorted but the ignition has me scratching my head. In the picture obviously wires 3 and 4 are the feeds (both black with silver band). So 5 will be...
greetings :)
I’m taking a spur from a ring final.
A fused connection unit will be controlling the spur.
FCU will be mounted on a metal backbox flush in a brick wall.
I’m planning on using a junction box to break into the RFC, and taking the spur cable to the FCU.
My question is, do both cables...
Hi,
The speed controller on my pedestal fan is broken and I thought of bypassing it by connecting the power supply directly to the fan motor. When I opened casing, I found two wires (Blue and Brown) coming in from the plugs end and four wires (Red, Black, Blue and White) coming from the motor...
I have had a Sunnyboy 4000-TL 20 for 7 years now and I am getting an error every few minutes which is
PE connection missing (9)
I have a Sunny Beam monitor which shows the power going up in a nice curve on a very sunny day but the power seems to drop when the system is generating more than...
Was having a look around local caravan dealers today, and as I know lots of you want to know the correct way to run a supply to a static caravan, I thought you might be interested in the attached photo which shows how a professional would do it! Also you also don't need the installation on a...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.