continuity

  1. B

    PIR Continuity

    I bought a PIR for an installation the other day and I was intending to use it for a contact but as soon as power is applied the live and switched live have continuity whether the PIR is triggered or not, I’ve tested a couple of different PIRs already installed and this doesn’t seem to be the...
  2. T

    How would you do earth continuity on ring circuit in two core MICC cable?

    How would you do earth continuity on ring circuit in two core MICC cable?
  3. Q

    Do you test the continuity of an installations main incoming earth

    This may seem like a stupid question but when testing for continuity using the long lead method I know you test the water and gas bonds etc but do you test the incoming earthing cable. I ask this because reading guidance note 3 it talks about the earthing conductor to be tested and I am slightly...
  4. M

    Ring final no continuity on live ends r1

    Hi, Im new to fault finding, Im on a job where there is no live to live continuity on the ring final circuit which supplys the sockets to the whole house, with new flooring recently installed I cant access the floors, im assuming there are many jbs because its a 1960s property, if I connect one...
  5. L

    UK Testing

    On a continuity test on existing lighting circuit, do all bulbs have to be removed, what if there is to many or some can’t be reached. Trainee Electrician
  6. D

    Ring main continuity test

    I'm not sure if this is a reasonable question or so stupid it shouldn't be asked. If the latter than I apologise and hope I don't get too much negativity back. So I want to perform the test Continuity of ring final conductors on an existing ring main. Because I'm lazy and its dark outside...
  7. M

    Ring main no continuity on live ends

    Hi, Im a bit puzzled, recently did a new kitchen install with complete new wiring from the cu, this included a kitchen ring, upon testing I have continuity on the n to n end amd cpc to cpc but no continuity on the live ends, Insulation resistance checks out fine on investigation using the half...
  8. C

    Glue Guns Failing earth continuity test

    Hi Guys Long time since I last posted but I have a problem I'm stuck on. My company uses a few industrial hand held glue guns. We have been experiencing repeated problems where the glue gun is failing on the earth continuity test. (Full test every 3 months) Typically 0.26 - 0.56 ohms. We...
  9. R

    Continuity of protective conductors...Initial/Periodic exam.

    Hi, With Referance to the current Initial verification and periodic practical exam. Continuity of protective conductors, including main and supplementary bonding. I understand using method one with circuit c.p.c, Connect line/c.p.c in connector blocks. Results provide, continuity, R1=R2 and...
  10. D

    How to test continuity

    Please can you help a complete novice. I have a light fitting with three clear wires. No colours, textures or codes. I’m trying to establish the L, N wires. I have a digital multimeter (see pics) Can someone tell me what to do step by step in layman’s term please? Which ohm do I set it at...
  11. E

    Trunking CPC Continuity.

    Hi Guys, an old existing 25mm - TP & N SWA Supply cable is glanded (No Banjo) to a 3" Metal Trunking end cap, & the remainder of the circuit cables are contained in the same trunking forming the CPC back to the Distribution Board. With a method 2 continuity & an insulation test, can you be...
  12. L

    Checking for breaks On A Long Cable

    Hi all, I know how to check for breaks on short cables from end to end but how would i check for breaks on a long cable ( over 20 metres) using a multimeter? Thanks
  13. N

    Earth Continuity Testing

    As part of my new job, we are required to test existing DC Power Racks for Telecoms. We are told to carry out a earth continuity test, then a IR test, then a ELI test. I may be getting a little complacent the older I get, but surely Earth Continuity is slightly OTT? I mean, we're proving an...
  14. michaelw6

    kt64 continuity boom!!!

    Hi guys been a while I've had alot going on in my life with ill ness and one thing and another. Any way long story short. I lent out my tester to a so called friend and he failed to say he had broken it! I found tin foil around the fuse and the continuity no longer works. After a massive...
  15. Z

    Question regarding signing off 32a ring circuit with broken CPC ring continuity

    I installed a kitchen ring recently. Went back to test after the builders had finished and found that the CPC is broken somewhere inaccessible, everything else tests normal. I’ve got continuity on live conductors, and even with the broken CPC, each socket is connected to the CPC and tests with...
  16. Savdar1810

    3P continuity L1 Earth

    Quick question for someone... Recently came across 3phase industrial heater, changing over a faulty isolator, in terminal box where equipment cable meets supply... I have continuity between L1 and Earth but nothing between L2 and L3 and earth. Disconnected earth from source and still the same.
  17. A032701

    Megger 1552 MFT continuity testing????

    hi I have recently bought a megger 1552 tester. it is in very good condition as it was just used as a back up. i have a slight problem with it though when trying to use it for testing continuity. basically i can only carry out one continuity test and then i have to turn the tester completely...
  18. cliffed

    Eicr no cpc continuity

    Remedials On Eicr,no cpc continuity,checked all sockets,still no luck. Gotta be a junction box,but near impossible to know where. Any ideas
  19. M

    Earth continuity on bathroom rad

    Hello Had to install a new towel rad in bathroom. Replacement narrower than original so had to adjust 10mm pipework. On breaking into stud wall I found that the green/yellow earth wire clamped to the rad pipe was chopped off and merely plastered over in the stud wall. Property 20 yrs old and...
  20. J

    Can a fluke T90 continuity tester be capable of confirming a new light fixture is good to go or not?

    Hi guys, I have wired light fixtures and hard wired a lot of cookers in the past, been all fine. I'm now training to be an electrician, the course itself is level 1 electrical installation. I have just bought my first continuity tester which is a fluke T90 and wondering if this is good enough...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
This website was designed, optimised and is hosted by Untold Media. Operating under the name Untold Media since 2001.
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock