Hi all,
I bought a Taylor Wimpey new build and had under cupboard lights put in the kitchen. 3 years on and the first one has gone out but when I unscrewed the casing to see how to change it, I am completely baffled!
Can anyone tell from the pic what I need to do/buy to change this, or do I...
Morning everyone...
I posted on here last week regarding an earth wire I found in my cupboard and got some really good advice which work... Essentially... Pulled a floorboard up and got some slack to tack it to the wall.. Which has worked a treat.
My next problem is 2 socket plugs on either...
Hi all. Some advice sought.
I have 2 lights under my cabinets they plug into the wall sockets below them.
I now want to hardwire the lights as i got a new cooker hood fitted and the spark pulled the power cable out so its now accessible to use. Previously it was hidden. So it looks like a...
Hi
I am running a new upstairs lighting circuit and need to find a route down to the consumer unit which is in the cupboard under the stairs. The easiest and least disruptive route would be via the airing cupboard, in trunking, then under the floor from which I can drop down through the ceiling...
Hi guys , new here and looking for a little advice . I went to see a job ( consumer unit upgrade ) and when I had a little scout round I found a wet room that had been stolen from the end of a garage . The spur and lighting were all outside zones but the room itself was 2.5 x 1.5 m and at the...
HI all,
just need clarification on bonding of a mains cupboard please.
Setup is
Mains cupboard 2mtrs wide and 6mtrs long
10 cutouts feeding 10 flats , has meters then tails to cutout then 25mm concentric to each flat
5 water tanks are in there and cables from flats feed the immersion heaters...
Hi all, first post on here but have been visiting the site for a while.
Here goes as it seems to be a bit of a grey area this one! -
In my bathroom there is an airing cupboard with a full size solid door on it at the end of the bath which houses the combi boiler. Originally the combi was...
What yous all using for under cupboard lights , and is quick fit
Depth can only be 30mm and length 300mm and don't want to be strip light if can help it,
Thx
Hi,
Just need some advice, what's the best way to instal under kitchen cupboard led lights.
First chase out the wall lift up flooring and connect to the Lights all ready wired up
2nd come of the socket directly under the new cupboards, due to being led the lights will have a transformer to...
Im currently doing a EICR report they have a socket in a airing cuoboard which used a to have a shower pump plugged now has the vacuum.charging. the distance from the bath is well within zone 2 but is in a seperate cupboard what C classification would you give this?
there's a boiler in a cupboard in a small bathroom. Would you install CO in the bathroom outside the cupboard, or would you install just outside the bathroom? In bathroom it should be outside of all zones etc, just access from above is very limited.
Hi
I'm looking to fit a light in the cupboard under my stairs, there is a single socket on the wall next to the cupboard door in the hallway with the wires clipped on the inside.
Not certain yet if this is a spur or on the normal ring circuit but if it's a spur then could I possibly fit a 13a...
Brns
Thread
cupboard
light
lighting
media
socket
stairs
switched
under
youtube
Hello,
The layout for my kitchen, which is not installed yet, is such that there is a free-standing dishwasher and washing machine on either side of a cupboard which has the kitchen sink over it.
My builder who recently re-wired my house has installed the wiring so that the plug sockets for...
Hi as above i currently have a Radial from CU in cupboard that powers one socket (powers 13a heater) outside the cupboard can i (DIY) add a new socket inside the cupboard between CU and existing socket? The intention to have a socket in that cupboard to power a chest freezer
Thanks for any...
So I thought, arrived at the house and found the plumber had moved the boiler to the loft(not a problem), the customer required the programmer to be moved from down stairs to upstairs outside the airing cupboard. I thought okay looked in the a/cupboard and found the connection box for all the...
How do people put in feeds to under cupboard lights? I would normally run T&E to a slim pattress or small white project box mounted on bottom of eye level cupboard to joint to the lights, interested in what others do?
Hi, I have a 6 gang grid plate, which has switches for my Fridge, Freezer and Dishwasher, and each has there own connection point around the kitchen for the respective appliance. I am wanting to move the connection point for the fridge about 150cm, and lower the freezer one about 20cm, and...
Hi guys just wondering if someone can clear something up? Been to look at a consumer unit change, but old one is located in the meter cupboard. I have heard in the past that consumer units can't be placed in the meter cupboard. Just wondering as I am replacing and cables go there, can I just...
currently took over someones job on a control 4 system "huge home automated system" due that being an extra they paid my boss separate for this. alot of lighting has Big transformers which had to be put local to the control 4. doing this i had to make connections "wagos and tape" due to many...
Mike Blair
Thread
client
complete
connections
control
cupboard
customer
electrical work
transformers
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.