disconnected

  1. G

    Cloth wiring outlet box load wires got disconnected, how to identify hot and neutral

    Hello all, I have an outlet box in my house built in the 1920s that I am changing to a GFCI. The wiring is cloth wiring so I have a hot and a neutral. On this outlet box I have the hot and neutral line wires coming in from the bottom, and on the top I have 2 load wires which go up to the...
  2. davesparks

    Disconnected CT's and EICR coding

    I'm having a bit of a brain fog moment (changing medication is such good fun!) and am looking for confirmation that I'm either right or talking nonsense. I've been to a job to have a look at why a set of ammeters aren't working, I've established the main reason they don't work is that someone...
  3. R

    Light removal, with connected neutral

    I'm looking to disconnect a two lights from a lighting circuit while leaving the main light connected. I can remove the second switched live to the two lights at the 2gang switch however the neutral is in a Jb under the floor boards somewhere. Is it acceptable to leave the neutral, earth and...
  4. E

    Touch control lamps only works when switch wire is disconnected.

    I have fitted a touch control switch to a lamp, (I have done many no problem)…..However in this table lamp with a cast iron base the device does not operate when connected to the base? But when unscrewed the light turns on and 3 stage dims as it should. Any ideas welcome please.
  5. N

    Light fixture. Ground wire disconnected. How to avoid death

    Hi men. This fixture began flickering then the bulb died. I put a new one in and it immediate made a popping sound and died. I opened it to look at the connections and it appears the ground wire is disconnected. I don’t see the other end of the ground wire or anything that with my limited...
  6. D

    Disconnected wires in wall

    Hi :) I'm looking to redo my kitchen early next year and am hoping to remove a defunct central heating timer from the wall and replaster. Once the timer is removed there will just be an exposed T+E from the wall which is disconnected (tied in a knot and buried in insulation) at the other end...
  7. K

    Incoming supply cable disconnected?

    Hi We’re currently having drainage Installed in our back garden, when the guys digging up concrete next to house came across what looks like a lead covered cable. They followed it along by digging up the area around it, until it entered a brick in the house, this is where the cable ends (see...
  8. A

    USA Is that a disconnected grounding system

    Hi guys, First of all I wanna say I'm not an electrician, so my knowledge is extremely limited, so sorry in advance if I say something stupid… :p And English is not my first language, so again, if I call some part with the wrong name, please just let me know I made a mistake, thanks! The...
  9. S

    Electric heater disconnected but still makes “click” noise

    I opened the circuit breaker to my 240vac electric heater. It still makes a “click” noise every so often like it’s trying to turn on. No heat come out. There is no thermostat. I’m confused. Help resolving this issue would be greattt.. thanks
  10. S

    Voltage on disconnected cable

    I think I may be going mad...job I was at today there was a strip light needing replaced, were 3 feeds & neutrals and a feed & switch wire at it. Was sure I marked everything ok but as there are ceiling panels going on before the light goes back on I thought I’d do a quick check, turned light...
  11. D

    Zs reading with main earth disconnected

    Morning, just checking a lighting circuit on a house, I have the main earth disconnected and still get a zs reading of 2.2 ohms. No evidence of an earth spike and bonding goes direct to henley block. Any suggestions why this could happen??
  12. B

    30v on disconnected cable?

    Recently pulling in some new lights in my kitchen, using the original feed in I ran 2 strappers and cables for 8 downlighters. Turned the circuit on and checked with my volt stick that the switching was correct and noticed the volt stick was going off no matter what position the switch was in...
  13. A

    Residual Current on Mains Tails - Installation Disconnected.

    I bought a new MFT1710 a couple of weeks ago and got a free clamp meter with it. (UNI-T UT210B, 200A Mini Clamp Meter). I finally got it out the box today and thought I'd try it on my mains tails to see if/how it's working. Surprisingly, with the consumer unit main-switch off, and the main...
  14. 1

    EICR flats communal areas

    Hi guys, I'm testing a communal area of flats, just lighting circuits mainly and in the board they go to a timer and then off out to lights etc. And all lights are on push switches or pneumatic switches. But I can't get any insulation resistance reading. It's like 0.13meg Is it the switches...
  15. J

    Cooker disconnected, RCD trips

    Recently had an electric cooker removed, the wire was left hanging out of the connection unit having been disconnected at the cooker end (all switched off at the consumer unit). I think the bare earth was touching one of the other two wires. My question is why did the RCD trip when I turned the...
  16. C

    Broken Neutral in Ring

    Hi I have a broken neutral in a socket ring, the customer doesn't want it fixed as he intends to re-wire the property in 18 months time. I have changed the consumer unit. Should I refuse to issue the certificate or put it in the notes. He has energised the circuit despite my advice not to.
  17. J

    Disconnected Neutal Still Showing Connection To Neutral (somewhere)

    hi i am replacing a consumer unit over and came across a strange problem with the neutrals when i isolated the old consumer unit. When isolated from supply im still getting 240v between incoming live and out going neutral. I have disconnected all neutrals from block (which clears it from...
  18. jon jordan

    V tac led driver tx's issues

    Hi all hope someone can aid me in this issue I've got why would a tx give out more output voltage on DC side than stated 30-42v Dc ( getting 57vdc) we have swopped tx over to other led on different circuit and all is ok 38v dc lights work put the other tx back which works in office onto...
  19. R

    Equipment disconnected and removed

    I have been asked to disconnect and remove a large 3-phase cooker from an installation in a commercial kitchen which is being cleared. Simple enough, isolate at DB, disconnect at local isolator, blank the exit hole, job done. The circuit in question becomes redundant, if it is re-used in the...
  20. D

    Buzzing RCBO

    Staff accommodation in a large hotel, was asked by maintenance guy to look at a DB. MK board with 3x RCBO's serving rings, and the rest lighting MCB's. One of the RCBO's was making a very noticeable buzzing noise,but otherwise worked fine. Disconnected cables and the buzzing stopped, IR...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
This website was designed, optimised and is hosted by Untold Media. Operating under the name Untold Media since 2001.
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock