element

  1. B

    3kw Immersion blowing sfcu 13a fuse about once a month...any ideas?

    On dedicated 16amp mcb Wired in 2.5t&e to sfcu (13a fuse) then 2.5mm heat resistant flex. Fuse has popped twice in last 8 weeks etc. Element R 18ohms. all seems ok? Should I just swap sfcu for 20amp double pole switch? haven't clamped to measure the draw yet as didn't have it with me. Cheers
  2. S

    Hortsmann E7 Quartz 1 hour Boost Not Working

    Hi.. Can someone help me out with this Hortsmann E7 heater's 1 hour boost. The light comes on when I switch on the 1 hour boost but the heater just does not kick in.. its not heating the water at all.. the main timer and the off peak heating is working fine .. its just the 1 hour boost that is...
  3. S

    Exposed element bathroom heater

    Hi, done a periodic on an oldish installation and there was one of those old pull cord operated bathroom heaters above the door with exposed heating element - what is the advice on this?? many thanks in advance......
  4. Worcester

    New element could revolutionsie Solar PV in the UK

    The CSIRO has discovered the heaviest element yet known to science. The new element is Governmentium (Gv). It has one neutron, 25 assistant neutrons, 88 deputy neutrons and 198 assistant deputy neutrons, giving it an atomic mass of 312. These 312 particles are held together by forces...
  5. sibbits

    240v heating element connected through 2 phases?

    i was asked to check why a tank heater was not working properly today an came across something im pretty sure is wrong. but was wondering if any of you had any thoughts on the element 240v rated was connected to two phases (one at each teminal ,no neutral) via seperate breakers, i dont know...
  6. A

    Can towel radiator be upgraded just by switching element?

    A client has a Dimplex TRS120 oil-filled 120W electrical towel rail. The element has packed up and before it's replaced I wanted to check whether the 120W element could simply be replaced with a higher wattage one, e.g. 175W (TR8404), as listed in the Dimplex spares brochure, a couple of lines...
  7. M

    Immersion Tripping RCD

    Hey folks just looking for some info here.. Im after changing my element for my immersion as it kept triping the RCD.. I installed a backer bt7 7" Rod, I wired it the following, (1)Live to The Element (2)from the other side if the element I connected it to the L on the immersion (3)Neutral to...
  8. S

    Faulty storage heaters

    Hi folks Was called to three storage heaters which have stopped working (all storage heaters in property). Two of the connection units into which the heaters are wired have neons, and the customer says these light up when the storage supply is on over night (so problem is not with supply or...
  9. C

    megaflow elements not heating up, despite element and stat testing fine

    Hiya, got an old heatrae sadia megaflo which looks over 10 years old. Just got this flat as its been empty for a while. Turned it on but no joy no hot water, there are 2 elements, one normal and 1 boost, tested the supply to both of the two radials supplying the elements and have 240v, have got...
  10. S

    Replacement twin grill element not working - other possible causes?

    The grill element blew the other day and I ordered and received a new one, fitted it and it's still not working. Could it have blown something else withing the cooker? All 4 wires are connected but there's no heat. The grill fan is working. I am stumped. The cooker is listed as a Hotpoint UY46...
  11. L

    Britannia S1-E10T Main Oven Tripping RCD

    A customer has a Britannia range cooker which trips the RCD everytime the main oven is switched on. At first the problem was intermittent and progressively worsened until now it happens every time the oven is switched on. The RCD trips even with the oven temperature setting on minimum before the...
  12. C

    Immersion tripping RCD

    HIi guys, Had a call out to a property today and looking for a bit of advice. As stated the RCD trips whenever the immersion heater kicks in. I have disconnected the incoming cables and Insulation Resistance tested them and they come out >200MOhms which is all good. The element is a Theeta...
  13. O

    Electric towel rail element?

    Hi, have been asked to install an electric towel rail, when I looked at it it appears to be a "plumbed" towel rail, just two opening each side for central heating pipes. I have looked on line and seen you can buy the heating elements to screw in, is it just a matter of filling with water and...
  14. B

    2kw circular cooker element

    Any ideas where I could purchase a whirlpool AKZ456/IX oven element? I've found a few online suppliers, but I'd like to fix the thing in good time for our Sunday roast. Plus I enjoy actually going somewhere, to meet someone, to purchase something, not "banging it into Google 'n' see Wat...
  15. B

    EICR code

    Hi Guys had to do an EICR today for a job on which the installer hadn't certified. Everything was okay but I didn't know what code to give for the following; the immersion was supplied via off peak supply on its own circuit but the top element was supplied via the ring main? I remember...
  16. L

    double element immersion heater wiring

    Hi Guys I've just come across an old immersion heater which I have never seen before and wonder if you can give me a link to a wiring diagram. Element in at the top, two elements (different lengths), one thermostat, two cables coming in so each element separately switched, BUT one neutral cut...
  17. C

    4 Rointe Heaters for sale

    Hello all, I've got 4 Rointe heaters for sale (used, bought in Jan) 3x 7 element and 1x 3 element. If you're interested please get in touch :)
  18. C

    4 Rointe Heaters for sale

    Hello all, I've got 4 used Rointe heaters for sale, 3x 7 element and 1x 3 element. If anyone is interested please get in touch.
  19. R

    Changing towel heater element question...

    Hi, I need to replace the element in my towel heater. Unfortunately the cable trails under my sealed bath before reaching the fuse box, and so I would like to rewire the existing cable into the new element. Please could someone more knowledgable tell me how to remove the seal on the element...
  20. W

    New Zealand side entry element into immersion tank

    can anybody tell me if theirs a standard size for a domestic immersion tank element ( side entry ) I have only ever fitted elements that go into the top Thanks

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
This website was designed, optimised and is hosted by Untold Media. Operating under the name Untold Media since 2001.
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock