I have been asked to disconnect and remove a large 3-phase cooker from an installation in a commercial kitchen which is being cleared. Simple enough, isolate at DB, disconnect at local isolator, blank the exit hole, job done.
The circuit in question becomes redundant, if it is re-used in the...
Hi,
1) To comply with the latest Reg's I assume that 230v 16A sockets for general use, now need RCD protection.
2) If the same type of outlet is for additional isolation of fixed equipment , an RCD is not required as long as it is labelled that it is not to be used for any...
The company I work for are responsible for carrying out all the testing in a high profile chain of stores. The customer is of course expecting everything to be done correctly so they are fully complaint. My company has said that any appliances that are located above the ceiling or in voids...
antony73993
Thread
advice
appliance
equipment
items
moved
portable
portable appliance testing
testing
Hope I'm in the right bit for this question
Just recently acquired a Megger PAT3 Tester which will be used for 110v leads / tools etc at work
Then the question came will it be able to test the office equipment - it will be ok for the kettle etc
BUT will it be ok for testing the Computers...
I have a Fluke 1651B tester. It was quite reasonably priced and seems to do the Job. However, I was after some advice on this product, for instance is it suitable for testing in a domestic property? Secondly, I want to eventually complete the C&G combined testing and inspection course. Would...
In an office environment...
So please tell me I'm a dunce on this one (I'll gladly wear a hat with a 'D' on it) but one thing I've never really got with PA Testing is when testing Class 2 equipment part of the test is one where you need to use the fly lead to clamp to some exposed metal part of...
What are the rules for sockets on an island in a kitchen. Sockets to be fitted to counter top. Also are there any recommendations on which sockets to use?
I have seen an excel sheet in calculator to calculate the size of transformer.
There are option to put the vales of Kw,PF,Qty and Equipment D.F.
I could not understand what is D.F.
What is the equation to calculate the D.F and equation to calculate the total load D.F?
Hello is there a way to test thermocouples with a meter other than via resistance test as sometimes you have to test thermocouples at diff temps so unsure on whats a good reading? I usually have to test something like a PT100.
Bit nervous about putting this on the open board, normally stick to the trainee section.
Hope i can get some help. I have recently qualified so dont be to harsh if im not 100% correct.
Ive been asked to help an older spark to pull a a 3 phase SWA cable. Ive been asked to design the circuit...
Hi All,
I hope I am posting this in the right forum, assuming that I am allowed to advertise items for sale here at all (sorry if this is the wrong section)....
Anyway, the equipment I have from my old business for Sale are the following with Current RRP prices (a lot lower than why I paid...
wulfruna77
Thread
business
complete
equipment
for sale
pat
pat testing
sale
starter
testing
All,
I have my niceic inspection coming up soon and am a little confused about the requirements for a 2 pole voltage detector. According guidance note 3, a multifunction tester, multi meter or a volt stick can't be used which is fine, but what I want to know is if a clamp meter capable of...
Looking for help on the following. On a site we have 3 10000 litre diesel storage tanks all built to the relevant standards however the pumpset is fitted with a standard 13 amp plug top plugged into a metalclad twin switched socket. I am sure this is not right but cannot find the relevant regs...
brett2012
Thread
diesel
electric
electrical
equipment
storage
supply
I have been asked to quote for around 12/14 properties and the spec requires all the AC equipment to be mounted inside the consumer unit.
can anyone recommend a good generation meter?
Also is it OK to fit a standard DP switch as an AC isolator as long as it's lockable ?
Consumer unit will be...
I've just got into the self employed/self assessment loop. I don't know which way is up after reading so much bumph. HMRC site just takes you round in circles. Any pointers would be greatly appreciated. I shall be using Cash basis tax format. So does anyone know :- what I can claim for, how much...
Hi folks,
Will be fitting first AMD3 board later this week. Using the Wiska spring tails kit on it. What is best way to drill a 40mm hole through the casing? I have cone drill bits up to 30mm and also have Bosch power change holesaws.
I found the cone drills much better in the past when...
These are my EICR limitations please can I have your opinion of these and any suggestions of any additional ones
1. As a minimum, 30% of electrical accessories will be visually inspected unless prevented( I.e. Artex ceiling)
2. Zs values inputted will be calculated except socket circuits in...
Breeze
Thread
access
appliance
eicr
electrical
equipment
limitations
point
Calling anyone in striking distance of Cardiff equipped with a PAT tester and preferably electrical / electronic troubleshooting background. I need to PAT test some electronic kit tonight / crack of dawn tomorrow morning, but can't get there myself. It is specialised and expensive stuff and...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.