floor

  1. F

    snug stat controller for under floor heating

    recently installed underfloor heating in my glass room 16m2 the under floor heating is 1800w which im told is 160w per square metre anyway issiue is its not reaching the temprature im calling for in fact ive never got it above 22 degree c it can take about 8 hours just to reach 19 any help please
  2. pe2dave

    dry ufh. Floor temp probe positioning?

    Arranging ufh in kitchen+adj utility. Lots of conflicting advice re probe position. (What makes sense to me). 1. Fit in conduit for ease of replacement. 2. Fit 'close' to heating element (which is what it is sensing). Without touching. 3. Fit as close as sensible beneath the controller on...
  3. N

    New single floor office advice please

    Customer will be hiring a qualified sparks, but can anyone give me guidance as to how a single floor open plan office should be wired in terms of circuits? There will be 3 islands of 8 desks and 3 of 3 desks, each desk served by an under-desk 4/5-way with a Weiland-to-13a lead. 13a sockets will...
  4. James Harrison

    Electrician Jobs Unidare Storage Heater with Under floor air flow broken

    Hi, I'm trying to help my elderly dad who has a Unidare Storgae system with underfloor air circulation. The motor appears to have stopped working. Can anyone help. I'm in Winchester, Hampshire. Many thanks in advance.
  5. B

    Ground floor lighting trips out mcb

    Hi everyone, My first post but straight in with a couple of issues. I'll start with a 6amp MCB that keeps tripping out relating to ground floor lights. For your info: There is 10 x 3w led recessed lights in Kitchen, 8 x 3w led recessed lights ,plus a main central Led light (approx 100watt...
  6. Steve93

    "Arena" floor boxes.

    Need to install extra datas into empty floor boxes. they are arena? printed on the front. anyone know where I can source data modules and sockets for these?
  7. V

    Terminate live feed from tiled floor?

    Hi newbie here. Actually I'm a chartered electronics engineer but am often mystified by the dark magic of domestic wiring! I have a kitchen counter fed by a live feed which comes up through a quarry tiled floor. I want to move the counter and disconnect that feed. I obviously don't want some...
  8. T

    Floor Light Help

    Hi y'all, First post on here, One of my clients wants LED floor lights to replace their hallogen's. The floor is in the kitchen & is marble. The cutout current is a square, 150x150mm. I've installed one to the client as shown: However the client doesn't like that slight rise the plate has. I...
  9. R

    Ducting for hob in floor

    evening all, Been to look at kitchen job today. All pretty straightforward except for self venting hob. The hob will be in an island about 1.5m from external wall. The floor plate is already down and there will be 50mm celotex and then 75mm screed on top. The ducting kit with the neff hob is...
  10. T

    Potential earth loop impedance issues for second floor flat

    Hello! After years of renting I'm currently in the process of purchasing our first property. We've had an offer accepted on a 1 bedroom flat in Surrey. However there are questions over the electrics, and knowing little about electrical wiring I'm a bit stumped on how bad the electrics are and...
  11. O

    MF smoke detector installation for ground floor

    Hi All, Moving inappropriate ground floor smoke detector installation from hall corner to middle of ceiling. Original wiring is OMGrade under flooring above (currently lifted); JB (not MF) feeding mains and interlink via even nastier chocbox housing plastic screw connector box. Just about...
  12. Marcus Vaughan

    Concrete Floor in Extension

    Well - I recently rewired a house and planned ahead for a proposed single story extension. The main house is now finished and occupied. Carpets - the lot. Cables are under a suspended timber floor in the kitchen and the plan was to extend these circuits (sockets and lights only) into this new...
  13. M

    Low Ze, high(ish) R1+R2, Got a plan but just had an idea

    So Ze=0.02 and R1+R2 = 0.73 on a first floor ring main. Nearest submain is about 35m away, so that Ze's plausible, and even a slightly indirect route makes Ze=0.03 realistic. So MCBs are going to need changing to Type Cs. Unfortunately for that first floor ring R1+R2 of 0.73 is too high for a...
  14. S

    Twin&earth and SWA installed loose on floor

    Hi All, The contractor working for Magnet Kitchens at my brother's house has run the sockets ring in 2.5 T&E, plus an SWA for the cooker supply, by laying these cables on the floor under the units. I'm fairly sure this isn't acceptable - at least these cables should be clipped up against the...
  15. D

    Running cable over steel beams below chipboard floor

    My builders have left a 20mm gap above the steel beams supporting the new first floor by setting the timber joists 20mm above them. Is it acceptable to run cables through the gap and over the beams? Cheers Dave
  16. PJElectricalSW

    Electric Under Floor Heating Survey

    Hello everyone I wondered if you would be able to help me with a project at the moment, I am looking for information about your experience with electric UFH. I am not going to lie to you, I do work for a UFH company so you will you will be helping me massively with my current project. I would...
  17. E

    recessed floor lights and idiots that install them

    yet another new installation ruined in less than 5 years due to terrible workmanship, -not a single drainage hole in 24 lights, -about 8 of them full to the brim with water as half of the lids werent even secure making the ip67 rating ip-zero -insulation stripped all the way to the copper on...
  18. C

    3 zone valves (underfloor, 1st floor rads, 2nd floor rads

    Hi, so I have 3 zone valves in place for my heating; 1 - for underfloor heating 2 - 1st floor heating 3 - 2nd floor heating for some reason the plumber has put a zone valve at the pump of the manifold. The 2nd floor has a missing room stat cable so will have to opt for a receiver for a...
  19. D

    Wet Under Floor Heating Modification

    Hi Guys. I have a flat with a 9KW electric boiler, dedicated for the wet underfloor heating system. The tenants have reported that all the digital room stats were not working, as when they increased the temperature to get more heat, nothing was happening. Within 15 minutes in the property I...
  20. J

    Can incoming mains run above ground under suspended floor?

    Hi all. I'm looking for some expert advice on the above. I am having an extension built and the footings are a raft slab which can be built/poured under the existing incoming mains cable (it's in a black pipe approx 50mm dia). There will be a suspended floor approximately 100mm above the...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
This website was designed, optimised and is hosted by Untold Media. Operating under the name Untold Media since 2001.
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock