Hi been a while, im writing a report and need to know if there's a specific term for the (?) front of a dist board, as opposed to the inside of a dist board? what im trying to explain is where all the MCB switches are; top of my head it would be something like "console" (probably not thou) or...
Hello All
Has anyone come across a problem fitting the front cover on the Hager Design 10 board over some RCBOs and a Disconnector switch? The hole in the cover doesn’t line up exactly with the devices and needs a bit of a push up to get the cover over them. Ie engage hole on underside of...
Looking for some assistance here as I have received different bids from different electricians. We live in Florida and have a Generator for emergency use, but have no way to power the house save for an extension cord currently. We are also remodeling our kitchen and are wanting to upgrade our...
Good Morning everyone.
Quick question regarding a sub main from a TNCS supply feeding an outbuilding on TT.
This is a domestic installation not agricultural.
TNCS supply to house feeds High Int. CU from which 4mmsq 2 core SWA feeds an non attached rear building.
THE SWA of the sub main is...
Citroen C4 l 2004 front left ABS wheel speed sensor fault.
Hi, ABS and ESP lights up on the dashboard.
Im getting a reading on Kph when driving on three sensors, except for the front left one.
The left front wheel speed sensor has been replaced plus the ESP module and pump, and the...
Hello my leccy friends. I need advice on installing front outside lanterns. Basically I already have 2 wall lanterns either side of garage. One by the drain pipe. It looks very nice with philips hue bulbs. Only thing is, it looks off as there is no light on the right side which the porch ends...
Hi I’m upgrading the fog lamps on a 2013 Range Rover sport to combined FOG and DRL got the fogs working but have a single wire to be connected to an ignition live, where will the closest ignition live wire be
I’m looking to fix a previous install. After having some rendering I have a feed that’s in 10mm T&E and I’m looking to replace the conduit. The gate is being replaced. I’m just looking for an adaptable box that I can have conduit come out the front.
I’ve decided to have the conduit come out...
Looking for quote for Front right indicator fix.
Front left and back right and left work fine.
I replaced the Front right with a new globe and it didn't fix it.
When I look closer there are 2 wires that appear to be going across the back of the headlight to the indicator and one is cut.
Any...
Situation.
Domestic TNS
Main consumer unit fed direct to incoming.
it has an upfront single pole RCD works fine. No main switch. No double pole isolation available.
Is this a potentially dangerous situation due to single pole Isolation?
I feel I can’t bring myself to give a C2 on an EICR...
Hi, I’m about to get some fitted wardrobes installed which will cover 2 plugs sockets. The wardrobes will be fitted wall to wall, so only front fascia visible
It has been suggested to move the plug sockets to the front outside face of the wardrobes ( the end units will have stable doors and...
I have an interesting one here. Not my install.
Here is a three phase old style Contactum 12 way distribution board.
Very first issue is that the front was accidentally thrown away by builders a year ago. The new equivalent is different dimensions.
It currently has very a creatively installed...
I've been asked to 'remove the light cable over the front door' so as I was passing I decided to take a quick look before contacting the tenants.
Picture is taken from the path, the head, meter and CU are in the storm porch outside what is now the front door. Presumably the cable I'm to remove...
Ok I have a room that I’m putting a ceiling fan/light in where there wasn’t anything previously...I want to grab the power from a switch that runs the front porch light...I have tried various things and have looked on various YouTube vids...can’t seem to get it working ...I have a double switch...
My house is Victorian and spread over three floors. The plug sockets through the front slice of the house across all floors don't work from this afternoon. The fuse box situation is pictured. None of the buttons has tripped - I switched each one off and on in turn to confirm they are still...
I hope someone can help me- I have installed new foglamps on my car. A new switch is also installed, and all wiring is good. I have also checked the connections at all points with a multimeter, and a probe. Turn the headlamps on, this enables the foglamps front and rear to be used. Headlamps and...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.