x5 recessed desk sockets and leads all brand new
These are approx £80 for the socket unit and £10 for the lead you need for them
Need the space back so will sell cheap
Any offers?
Hi,
Had a problem recently. Switch fused spur fed off ring main to control 6 x t8 5ft fluorescent tubes works when it wants, tried replacing fuses and tried a new spur, and keep getting the same problem. Its not overloading and havnt come across this before.
Any ideas??
Thanks
Hi,
Just moved into my new house and have a GreenBrook KingShield T205-C Fused Timer Spur Switch attached to the immersion and controls the hot water in the house. The immersion doesn't seem to be working either (by the way)
As it doesn't seem to be heating the water when I turn it to the...
I've just removed an old fused electrical heater fitted in the middle of the ring circuit and am now left with the hole and wiring (see pic). Ideally I want to just cover this up with a bit off plasterboard so it looks like nothing was ever there. Is it OK to do this or is this deemed unsafe? I...
Hi everyone,
Yesterday my sister switched on the bedroom light and all the lights o the top floor went out! there are six lights in total and none of them work at the moment. The lights on the bottom floor work and all the plug sockets on both floor's work fine too.
I know next to nothing about...
Hi,
My central heating wiring centre (Honeywell S Plan) is hanging off a 13a plug in the garage which is plugged into a double gang socket with integrated RCD at waist height close to where I would to fit a sink.
I'd like to move the wiring centre much higher up the wall so it is out of the...
I wanted to know if a radial circuit that has a fused spur at the end of the circuit can then feed a double socket if I use a 13amp fuse in the fused spur? Also would that then have enough power to run a washer and maybe a chimney hood fan above a cooker hob?
Now I completely understand why cables must be fused down when a lower size cable is connected to a larger sized cable. To ensure the cable does not burn out from current that it cannot take.
Yes i know this
Now current doesnt go anywhere it isnt in demand for so if a spur off of say a 6mm for...
Hello folks, I have just finished installing a WarmUp DWS600 loose wire system in my bathroom.
A little more on it here, but essentially it's rated at 0.6kW / 2.6 amps.
Warmup DWS 600 Loose Wire Underfloor Heating Kit -...
BobG
Thread
bathroom
fuse
fused
installation
loose
system
underfloor
wire
Adding an extractor fan off of a 6A lighting circuit.
Installation instructions specify a local isolator (as I would anyway) so 3 pole isolator will be used.
Switching L SL and N however should I have an FCU upstream of the live?
It would be 6A fused as specified which seems pointless the RCBO...
Got some coastal apartments which have a mixture of downlights, pendants and 5A round pin wall plugs all controlled by conventional light switches and everything is switch fed. OCPD is a B10 mcb which if I derated it to a B6, would still be over the 5A rating of the sockets and plugs. All the...
Before I start, I know this is not usual but I want to know if it's against regs.
I'm testing a conservatory ring, feed from a fused spur. There's a Live-Neutral IR fault between two of the three sockets.
The cable is embedded in the conservatory bare block wall.
If I just disconnect the faulty...
Hello all,
I am looking to install an xpelair 12v fan in a bathroom with a humidity sensor (model no. 92970AW). I can't quite work out from the instruction manual whether the humidity sensor is in the fan itself or in the transformer. due to the size of the bathroom and the position of the bath...
Query regarding a Passive RCD fused spur unit protecting a bank of 4 led downlights supplied via switched live and nuetral. I have been asked to replace the downlights. Cant be totally sure but i think RCD spur was to protect the (addition)of the downlights. The rcd is passive so will remain...
Hi, came across this today, double width cutout, never seen it before. Not sure if it could be fused on the neutral or whether I am worrying with no need. Any advice appreciated. (Haven't pulled the cutout obviously, even though it isn't sealed - I have a feeling it might be too stiff to pull...
Hi,
If you have a luminaire connected to busbar trunking via a fused "plug" is this then considered as a fixed appliance? And if so, if you were to change that luminaire would that constitute an change to the circuit, i.e. Would you need to issue a MWC? I am also assuming that if the plug is...
Hello, need to run a supply to a tyre air line at a petrol station. No info on it but think its probably around a kilowatt, definitely not over 3kw.
Should probably be on its own dedicated circuit, but going to cost more.
There is a socket inside that I could spur off and save alot of extra...
Hi, I'm brand new to the forum, so please go easy on me! :-)
I'm building a large extension, which includes a new en-suite bathroom. I appreciate that the work has to be done by a suitably qualified electrician, and is obviously subject to building control sign off. That said, I have been...
Alan Kerr
Thread
bathroom
bathroom electrics
electrics
fused
isolator
various
just wanted to quickly introduce myself and need some of your advice.
A little about me. I'm an IT professional for the past 15 years. I've started to learn the basics in electrical and can change electrical sockets. I've learnt this via online and brother in law. As probably you can tell I'm a...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.