likely

  1. littlespark

    Gym treadmill likely load

    Got an issue with gym equipment. ( I keep telling my wife I’m going to the gym, but she doesn’t believe me!) The gym owner says the circuit for treadmills trips out every now and again. I went there last week to find a 16A type C RCBO supplying 1x metal clad double 13A socket. From here, there...
  2. S

    Is this likely to be asbestos?

    Cut this out of a kitchen wall. Like a cement board on a steel frame house. 1950s build .Some kind of mesh in the middle. Should I get it tested?
  3. T

    Looking at moving to New Zealand - qualis likely an issue

    Hi guys I’m looking at moving to New Zealand as soon as Covid allows and just have a few questions regarding required qualifications to work in NZ... I work in events (temporary power solutions). Until recently I wasn’t qualified as it isn’t technically required to carry out this work as I’m...
  4. T

    Oven grill

    My zanussi free standing ovens grill trips the main fuse after use when switching off. It most likely an element issue?
  5. Z

    Bulb staying on

    I have a 6 bulb ceiling light. Just recently when i switch it off at the wall only 5 bulbs go out. Is this more likely to be a faulty light fitting or switch?
  6. 4

    Look at this Beauty Likely DIY job

    Potential customer has sent this photo. It is of a melted ceiling light fitting in a kitchen ! He believes this was done by a previous owner. The good news is that he recognises that he needs an electrician, bad news is that I have no ability to respond quickly. Anyone in near BS15 who would...
  7. polo1

    Assistance with likely BS please.....

    As above, anyone able to assist with the likely BS of this Lucy cut out fuse, (assuming that it's original!). I will "Lim" the box on the inspection report but interested in views.
  8. Soulsurfer

    Adding PIR sensor to existing outside light.

    Hi I am needing to adjust a 1 way switched outside light at a house in a couple of days to switch 2 way possibly with an ip rated switch on the way to the front door as it's only switched 1 way from inside the porch at present. I'm just thinking of instead of an exterior switch of using a...
  9. S

    What's the largest size array for a 60 amp cable head fuse? Single phase.

    SP Networks are the DNO. Smallholding with single phase and 60 amp cable head fuse. What's the largest size likely to get approval?
  10. E

    Steeple SMF100T inline fan vs Manrose MF100T

    Hi I made an ebay fan purchase fairly recently. I ordered what I thought was a MF100T, but was sent a Steeple SMF100T. It appears to be identical, was sent with the MF100T instructions, and has Manrose on the sticker. After a bit of internet research I've found out steeple is a Denman's own...
  11. L

    Most likely Electrical fault for this situation?

    Hello everyone, I am currently doing a level 3 Electrical Installation course and I am doing one of my assignments. I was just wondering if I could get any views on this question I've been posed. What is the most likely electrical fault for this Symptom? A fault has occurred on a lighting...
  12. S

    Use old immersion wiring to use for Sockets?

    Just discovered the old wiring for the immersion heater. We have very few sockets in old victorian house. The immersion heater wiring was left in a terminal block wrapped up in masking tape! I changed the old wylex fuses on the CU to use MCB, thankfully I switched the 16A fuse off for the...
  13. P

    least likely van to be broken into

    Hi guys about to buy a new vehicle as my estate has just about had it. Don't really need a van so was thinking of something like Nissan Navara. My question is from your experiences is a flat bed truck type vehicle less likely to be broken into than a van. I'm based in rural Suffolk. Cheers for...
  14. Rockingit

    AGA commissioning an induction cooker, are they likely to insist on a 45A supply?

    Have a customer made an enquiry about needing a 45A supply for a new AGA induction oven, as that is what is spec'd by the manufacturer. Explained diversity etc and said the existing 6mm supply will be sufficient, which he understands, but he is concerned that when the AGA installers turn up...
  15. J

    Obvious question more than likely.

    Second question of mine on here and it's one I've never got round to getting an answer for. Mains comes into a building through a 60A main fuse for instance. Why then are main switches rated at 100A or 80A? Does this mean any load above 60A would blow the main fuse before it blew the main...
  16. N

    Benefits of single grid switch?

    Hi all, Is there a benefit to using a grid switch if its only a 1 gang switch? Fair enough if you require a 3 or 4 gang grid switch but not if its only a 1 gang. I recently worked in a low risk mental health unit which used these. The building is fairly old so is this what was generally used...
  17. R

    Fluke 6500 reset access code

    I got a Fluke 6500 PAT tester off ebay but the access code is no longer set at default (9999). I suspect the previous owner changed the code, I've contacted him but he claims to have no knowledge of the access code. Without going to Fluke and paying loads of money, is there any other way of...
  18. C

    4g mobile phone network rumoured very likely to severely affect freeview tv receptio

    "Hello All", I read a few Days ago that the 4G Mobile Phone Network `Second Phase` of Transmitter installations / Upgrades is VERY likely to cause SOME areas severe problems with Freeview Reception - `Totally Blacking Out` some areas ! I noticed that one of the areas likely to be MOST...
  19. C

    4g mobile phone network rumoured very likely to severely affect freeview tv reception

    "Hello All", My Post about 4G Mobile Phone Network severely affecting Freeview TV Signals has been moved by Me to thre Freeview TV section. I inadvertently posted it on this section previously - "Sorry". Regards, Chris
  20. P

    High Zs Reading on Megger MFT 1552

    Can somebody help me please? I'm just finishing a rewire, and I've installed a GF radial cicuit in a large domestic property and am in the process of testing it. It's a new radial circuit, 2.5 T&E, 13 sockets, 20A type B breaker on an RCD protected board. My R1&R2 = 1.40 and Ze = 0.20, so my...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
This website was designed, optimised and is hosted by Untold Media. Operating under the name Untold Media since 2001.
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock