Existing double gang socket in the corner of a kitchen on a dedicated 12m length above ceiling 2.5 final circuit to CU, was used for a WM and a tumble dryer protected by a 32amp MCB.
I wish to keep this arrangement but on lifting floor boards above ceiling I noted entire run of cable/s was not...
Hello,
I'm seeking some advice on an overheating plug adaptor please. Complete amateur so please forgive any errors in calcs / assumptions / terminology. I've recently started using with an expresso machine in an Irish domestic environment (ultimately 230V 13A socket) but it comes with a...
I am trying to replace a mechanical switch from an OLD ice machine with an electronic timer. The existing switch has only 3 wires, a Black Power Wire, Blue Normally Open and Orange Normally Closed. The existing timer is activated by a capillary tube attached to the freezing tray. When power...
I ran 208 v power to a rottler em69p cnc machine. it calls for 208/240 v 3 phase. 60amp rottler em69 installation manual
everything is wired using 3 #6 hot and #8 ground
to 6/4 SO cord drop to the machine . inside the machine again the wiring is 3 #6 and #8. I checked voltages and got 208-209v...
Hello everyone. I've bought a second hand Bosch series 6 (2 years old, minimal use). The first washing went without any fault during the cycle, but after the cycle fully finished (10 seconds later), the machine tripped the fuse box. I've removed back and top lid to check if any wired connection...
Hello everyone. I've bought a second hand Bosch series 6 (2 years old, minimal use). The first washing went without any fault during the cycle, but after the cycle fully finished (10 seconds later), the machine tripped the fuse box. I've removed back and top lid to check if any wired connection...
Anyone have any clues? Faithful Brother P7600 stopped working, won't turn on. Assumed that the rechargeable unit has had it (it's certainly old enough) so removed and put fresh AA's in. Still won't turn on - display lights up, sometimes does an 'all pixels' kind of thing but never actually...
We have this Swiss-made Dixi horizontal borer from 1957, very nice machine still with its original DC variable voltage drive. In those days there were no VFDs, variable speed machine drives all used DC motors or Schrage AC motors, with the best DC units capable of better performance than VFDs at...
Hi There,
Homeowner here with no electrical knowledge, so go easy on me!
We've had our garage converted, and coming to the end of the project. We've had a shower/utility room (2.7m x 1.5m) added as part of the conversion, within which is housed a stacked Tumble Dryer on top of a washing...
Hi all,
Please take a look at the video. I recently have a arcade machine, but it is cause a buzzing/static sound. Can someone help me identify what is wrong with it?
Hi, the below says a washing machine is 800W....
https://unboundsolar.com/solar-information/power-table
...is that the average power over the whole thing including spin?
How much power does one typically draw during the spin phase?
Hi.
Did a call out just this morning as customer was getting shocks from Kitchen sink. On arrival I could see the sink was earthed and had good continuity back to the main bond. The client told me that it was when he was using the washing machine underneath that he had the shock when he...
Hi all,
I am trying to diagnose an issue with a BEKO WMB101433LW washing machine where it was reported (by the missus) that the drum has far more resistance than usual.
I've ruled out bra wires etc and anything between inner and outer drum and have isolated the issue to the high torque setting...
Sorry this question may sound silly, but I really don't know anything about electricity so I'm just asking to make sure.
So, recently I bought a machine from the U.S via Amazon. In the instructions of the Amazon page, it said to plug the machine into a 110V socket, but our countries run on a...
Hi, does anyone know how to wire the brown wire.? I shake it and then the brown/yellow green wire be loss from its original place, but i forgot where it was.
Thanks all
Greetings All. FTP. the electric keeps tripping mid cycle - not every time and not related to any particular programme. we have recently replaced the washing machine and the problem still persists and is probably more frequent now. it is not one of the usual suspects of latch, element etc. am...
Hi.
I have been having a problem with my AEG 7000 Series Washer Dryer (L7WEG851R) tripping my main fuse box over the last week. I am trying to diagnose what the issue may be. Here is what has happened so far. The machine is three years old, so it is now out of warranty.
Last week I ran my...
I let out a flat and had an EICR, carried out, to meet the new Private Rented Sector Regulations. The EICR has recorded a “C2” for an extension lead on a washing machine.
The lead supplied with the washing machine is about 1 metre shorter than is convenient for fitting the drainage tube back...
This coffee machine is three phase model number sm 105e
It’s three phase with 3 brown cables one neutral and earth
What is the cheapest way to wire it in?
thanks
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.