making

  1. L

    Hotpoint range oven making funny sound - fan motor?

    Hi All, Thank you for your previous advice - it resulted in us replacing our precious Smeg range with a Hotpoint; however we now have a new issue that I was hoping you might be able to advise on: The oven works nicely and the heat seems good etc. But it makes a pulsing noise when you're using...
  2. M

    Anyone heard of company called Scimark making domestic switches, outlets etc?

    Has anyone heard of company called Scimark making domestic switches, outlets etc? We live in a house built by David Wilson Homes who subcontracted electrical installation to Clarkson Evans. I need to source some replacement 13A 2 gang switched outlets to replace a couple that were originally...
  3. ferg

    Adverts making the forum unusable.

    I know they pay the bills but there are so many it's making the forum unpleasant to visit. Forum sponsors on the RHS. A banner type thing at the bottom that I can minimise. A banner at the bottom of every post. Ads in the middle of posts. At one point I had 2 lines of text on the screen and...
  4. Spoon

    making Faulty Towers again.

    So I heard on the news this morning that they will be reviving Fault Towers. Also see below. https://www.bbc.co.uk/news/entertainment-arts-64563839 I can't see this going far. Don't get me wrong, I loved the original (as you can tell by my signature) but there will be too many people...
  5. J

    Opinions on making safe

    What do you guys prefer to do if carrying out a ‘make safe job’ for example exposed conductors accessible to touch. Do you lock off (you may not be the person doing the work next) or do you disconnect the circuit and label what the problem is?
  6. S

    Wiring an A/C unit, making from in my panel

    I am looking to install an A/C unit. (3.5 ton York) I believe I need a 30 amp breaker. My panel is full but I have two beaker spots I will not use that are next to each other. My plan would be to pull those and replace them with the new 30 amp. Do I need to pull a permit? Location Edmonton, AB
  7. J

    USA Making 10/2 w/o Ground Pole Barn Subpanel Safer

    We have recently purchased a home in TX built in the 1920s, and the wiring is an assortment of multiple wiring events. There aren't any local codes as it is unincorporated land. The events in question are with the overhead wiring to the pole barn subpanel consisting of two 10 gauge solid-core...
  8. S

    Earthing mat is making me ill !

    Hi All Sorry for the lengthy first post and use of any non-standard terminology. I'm a bit of a novice when it comes to electronics, hopefully I've done enough due diligence so I'm not asking anything too silly lol ? I've bought a Grounding mat that plugs into the mains (earth wire only)...
  9. C

    Making electric car seat work out of the car as a stand alone chair.

    Hi all, I have a project to make a range rover evoque seat working outside of the car, Just the motion controls. I have a 12v 30amp step down transformer to give it power. Is anyone able to give me some guidance? I belive I just need to supply power, neutral, ground to the motor. Happy to...
  10. Lister1987

    Making the trades (or fundamentally that knowledge behind them) accessible.

    An idea has been swimming around my head since i started my journey to becoming a electrician; Are the trades (any) accessible to those with disabilities? What's everyone's thoughts on the matter? Let's not beat around the bush here, the trades are very physical and demanding jobs however I...
  11. P

    Making damaged wire safe

    Hi, I hope I’ve posted this in the correct place. Please forgive me if I have not. A little while ago I was drilling a bracket for my home alarm and hit an electrical cable. The cable in question runs from the fuse box to my cooker and hob. My father made a temporary connection when it...
  12. S

    Sockets making tv turn on and off

    Hi Everyone I have an issue that has stumped me. My TV turns it self on and off from standby to on and back to standby continuously but only in two separate sockets in the lounge. It seems to always have power but flicking between the two modes Plugged the tv in to every other socket on that...
  13. J

    Making one 12/3 wire into two 15 amp circuits

    How can I take a single 12/3 wire running 75 ft from a 20 amp circuit on the house to a couple outbuilding, each with their own 15 amp circuit?
  14. J

    removing a light switch, making it always live (UK)

    I've replaced a light with a low energy LED bulb which is controlled wirelessly, and now want to remove the old switch so that it is always on, and I can then control it with the wireless switch. Can I just remove the switch and connect the L1 and common wires together? It's an old 1-way 1-gang...
  15. Pretty Mouth

    Plaster board faced insulation - making good?

    Hi all. I'm after some practical advice please. Got a job to quote for, fitting a couple of gimbal downlights in a sloping ceiling in an attic room. The construction appears to be PIR (celotex or similar) insulation between rafters, with plasterboard faced PIR insulation over the rafters...
  16. J

    USA Help making a generator cord for my home!

    I just purchased a generator with a 30 amp twist lock 4 prong outlet. My house has a generator outlet that has 3 prongs, see the attached pictures. It appears as though the outlet was wired using the black as a hot and the white wire also as a hot. I am making a generator cord and I have...
  17. T

    Making the best of a bad PV installation

    I'm after some practical, expert advice on changing a solar PV system. Got a 4 kW system which I probably paid too much for in 2016-ish when FiTs were still a thing and which is annoyingly inefficient, mainly due to the Growatt SP2000 battery which only kicks in after dark, when the panels are...
  18. M

    Making a swithched fuse box.

    If i want to wire in a fuse box to my utv and make it switched when the ignition is on. Is it best to run a continuous cycle relay say 150amp then run from there to the fuse panel
  19. Padrag

    G'day! Making a big move...

    Good afternoon everyone! Australian Electrician here, Even though we're in crazy times at the moment. I'm making the move with my Partner from Sydney to the Republic of Ireland soon, and am hoping to learn as much as I can about my change of scenery on this forum. Also been scouring the...
  20. M

    Legalities surrounding lamp making

    Hello, I would love to pursue a career in hand made lamp making.I have researched all qualifications/certs needed for the legality of making lamps but found the information to be a minefield. I would really like to know what qualifications/certs/courses i need for the legality to complete to...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
This website was designed, optimised and is hosted by Untold Media. Operating under the name Untold Media since 2001.
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock