Evening all, got this rating plate on a portable feed augar motor, it's currently wired in some seriously past it SY cable, the farmer wants to renew it , I've suggested H07RNF as best choice, but I'm not clued up on reading motor plates to size it, I see 29 on the plate, and assume it to be...
We have some shunt-wound DC motors that are used are servos (so operate over a big speed range and in all 4 quadrants, motor and generator both directions) and one of them (0.25kW) has gone "lumpy". My suspicion is the armatures has some open winding(s) so the speed/voltage profile changes as it...
Here is the circuit parameters I am trying to build, I just can't seem to figure it out.
When the start button is pressed, motor 1 turns on
Motor 2 will start 5 seconds after M1 has started.
Motor 3 will start 6 seconds after M2 has started.
When the stop button is pressed, M3 stops...
Just been sent this picture my a regular client that plays with cars:
He says the bloke he got it from had it working in his domestic large garage which implies single phase and the plate does say 14A at 230V, but all the info I can find online is in french and seems to say its 3 phase only.
My...
Hello,
I have a 7.5kw 3 phase motor 400/690v 50hz. Can anyone advise what size and type mcb is needed for this please? It’s currently being fed via a c16 which is tripping now and then.
many Thanks
About 20 years ago I bought an old table saw from a local school. I only had single phase at the time so I changed the motor and switchgear as it was 450V. I'm thinking of buying a 3 phase 50s bandsaw and have the same problem, but I can't remember how to work out the size of the replacement...
Renault clio mk2 not cranking over. Battery reading good voltage. Changed starter motor for new one but same issue. Bench tested old starter and working fine. Noted that when I place jumer cable on negative battery terminal and then to engine to ground it starts not problem. I've taken off the...
Hi there,
This is my first time on this forum. I hope I am in the right place because I need some knowledge that I don't have. But first, I'm Niels, I'm 18 years old and I'm from the Netherlands.
Now here is my problem:
I've got an old electromotor that I want to fix. The first step in that...
Hello all
Just looking at a Samsung EcoBubble washing machine that's fairly new and been an issue for some time apparently.
It's in the sister-in-law's garage. She says she's had the Samsung guy out to it 3 times under warranty and it still doesn't work.
She has no idea what was done to it...
I’ve recently seen a motor wired directly from the local isolator to the motor terminal box in 3 core 1.5mm cable. The gland has been made off into a threaded hole in the motor terminal box and at the isolator end directly connected to the incoming swa from the MCC by means using a flylead. My...
This might sound like a stupid question so apologies in advance.
So I had a random thought in my head.
So I was wondering if I was to use a single phase motor to spin a three phase generator to create three phase power, would you be able to create more power then the single phase motor is...
create
electricity
energy
energy efficiency
generator
motor
phase
power
power generation
renewable
renewable energy
single
single phase
three
three phase
I have a metal lathe, 1.5hp, 3phase, 575v motor. Can I just replace the motor with a single phase,220v motor? Would all the lathe wiring , switches, relays work? IF so, what HP motor should I buy? Thanks,
My motor is 3phase induction motor of which has 3KW of output max. power and max. speed is 320RPM out put torque range is 80-120Nm So, which VFD is proper suitable for it, and how to choose it.
Have been asked a question which I am not 100% on, and I have never been asked before.
Motors have 6 studs inside the terminal chamber, U1, V1, W1, and then the internal wiring of the motor and the studs on the opposite side of the chamber read W2, U2, and V2. If the motor is a Star...
Ok, say you had a constant operating 25 or 60kw motor in the UK. How would you wire this up? What type of MCB, fuse, starter, overload protection, wire ect would you use? Basically the rules and typical setup that you would see out on the job.
2009 Lexus IS350 blower motor turns in the wrong direction and sucks air instead of blowing air out of my vents. I am trying to figure a way to make the fan spin the other way. I live on a small island and getting a new blower motor imported would take about 2 - 3 months to get here right now...
Hi all . I need help with a question thats been set by an interview panel . “
Describe a step-by-step DOL starter overload replacement and how you would check for the correct amps adjustment.” Any help would be greatly appreciated.
Hello all. I have a problem that I'm sure someone can help with. The electric motor I have (pics attached) has no ratings plate. There are no supply wires shown, just the internal connection box wiring. The picture of the wiring diagram looks to be single phase but the box wiring has me...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.