mounted

  1. S

    Minimum IP rating for wall mounted external industrial socket?

    What is the Minimum IP rating for wall mounted external industrial socket? It's to be outside & only used for plugging in a generator that will give house temporary power through a changeover switch in the case of power cuts.
  2. D

    Flush mounted pull cord backbox and theories

    Hi all, It just popped into my head about bathroom pull cord switches, do they ever have flush mounting boxes, every one I have seen has been surface mounted, and also, why are shower pull cords cut shorter, which I see in most places?
  3. K

    Surface mounted wiring into recessed box for boiler?

    We are now 18 weeks into a six week project. There are so many things that just seem a bit botched. I'd be grateful for any advice - is this usual, legal, acceptable? 1. The electrician suggested a grid pattern for down lighters but now that the plastering is done the lights are very off...
  4. T

    KWh meter din rail mounted for wylex board

    Hi so any ideas on din mounted MID rated single phase kwh meter? I am required to fit a meter for sockets in a unit. At the moment the sockets are fed from a 32a mcb in a wylex plastic D.B. older type. See photo. All suggestions treated in confidence and will be touted as my own brilliant idea...
  5. I

    20A Fused Switch or DIN mounted 20A RCBO

    Hi, My central heating wiring centre (Honeywell S Plan) is hanging off a 13a plug in the garage which is plugged into a double gang socket with integrated RCD at waist height close to where I would to fit a sink. I'd like to move the wiring centre much higher up the wall so it is out of the...
  6. S

    Ceiling mounted extract fan

    Hi. Not had much to do with domestic and subsequently have not fitted many bathroom fans. Have builders in doing my loft conversion and am wiring myself. Now the only place for the extractor fan is in the ceiling with duct run through void out soffit. Unfortunately I only just had enough height...
  7. F

    Virgin Cable - Flush Mounted Outputs...?

    Hello all, new member here....I hope you don't mind the post in your patch... The property we recently purchased had previously been cable connected – one Ominbox outside which feeds telephone to one room and three coax cable runs. Only two of these are likely to be used in the immediate future...
  8. J

    Grounding a Wall Mounted Data Cabinet

    I have recently taken over in the IT side of a medium company and one of the things I have noticed is a terribly installed wall mounted Data cabinet. I have spent the weekend sorting it all out so it all comes up to spec but wanted to clarify on some points. It is currently mounted on the wall...
  9. H

    PIR Sensor to replace switch

    I'm looking for a PIR sensor that will replace a standard light switch but the ones I can find are £40+, which seems a little silly considering you can get a standalone wall mounted PIR for about a tenner. Any recommendations anyone?
  10. Y

    Wall mounted tv

    In the middle of new house wire, have pulled 2 co-axles to every TV and cat 5e too every TV in the house and back to the switch room, the problem with the TV in sun lounge is that the wall mounted TV is about 7 meters away from where the sky box and DVD player etc will be, I have tracked and...
  11. R

    Kitchen sockets mounted to cupboards,

    Ive been given a job by a local builder who wants sockets for appliances mounted direct to the back of the kitchen cupboards.. Ie I fix surface mount boxes inside Base units He has requested no FCUs on show so these also in cupboards. How do I stand with this, I've always done commercial...
  12. J

    Is it OK to fit a socket with edges to a rounded surface mounted pattress box

    Hi, I was wondering is it OK to mount a double socket with edges onto a rounded edge surface mounted pattress box Thanks Jonny
  13. B

    Trunking for cable

    I have a job of running a new cable to a DBB. The 16A MCB is in place and the oven is rated at 3.9kw so needs to hard wired. The customer has tiled walls and will not allow me to remove them to run the cable. He wants the oven switch surface mounted. I have approx 0.5m of cable from DBB to the...
  14. B

    Surface mounted plastic patresses

    I dont do much house bashing and hate the surface mounted plastic pattresses. They are brittle and smash if put on an uneven wall,breaking the tabs for cable entry can even smash the box too. Then a good woman with a hoover or similar appliance can pull a double pattress off the wall:bow...
  15. L

    flush mounted split load fuse consumer unit

    can anyone recommend a flush mounted split load fuse consumer unit for amendment 3
  16. A

    13amp Double Socket with plug presented at 45 degrees- do you know a supplier ??

    Hi This question was asked some years ago on this forum but the link to the supplier is no longer active. I am looking for a Wall Mounted 13 amp double socket that could be mounted on a narrow kitchen upstand that would normally not allow the use of moulded plugs. as i see it there are three...
  17. P

    Din Rail mounted equipment ?

    I have been asked to quote for around 12/14 properties and the spec requires all the AC equipment to be mounted inside the consumer unit. can anyone recommend a good generation meter? Also is it OK to fit a standard DP switch as an AC isolator as long as it's lockable ? Consumer unit will be...
  18. S

    pir in garage

    customer wants 3 fluorescents in a garage to work off both a p.i.r (when door opens) and a switch can this be done or can he only have 1 or the other (existing power already there and all good)
  19. B

    Led flood light, 70 - 80w. Mounted about 4m up

    After some ideas, got a flood light to install to light a playing field for a fire drill. Supply is sorted spec is sorted. However it coming off a external building which is not much bigger than a normal door height. I'm looking for a mount to take this up to roughly 4m, but idearly not timber...
  20. P

    Amendment 3-compliant flush mounted consumer unit

    Has any manufacturer come out with a compliant flush mounted CU? The ones I can see have either a plastic back and a metal door or a metal back and a plastic door. It looks as if compliant CUs will have to have opaque metal doors. In this case I can't see the point of the door being some sort...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
This website was designed, optimised and is hosted by Untold Media. Operating under the name Untold Media since 2001.
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock