We have just moved into a house built in the 90's. So, I'm a retired electrician and was confused by the 4 x TT rods all connected within a metre of each other on one side on the house. I dont have any expensive test kit any more, but when I connected an electric fence energiser to the house...
Hi,
I'm new to the site and wanted to seek some advice thanks, relating to adding fused spurs to existing ring mains in a commercial premises.
Some of my other colleagues have been asked to explore ring main alterations, but they look after some site based kit and this is more related to...
I recently installed a new 15amp circuit breaker, and wired a 14-2 gauge wire to a brand new dimmer switch. From the dimmer switch I daisy chain wired 6 LED recessed lights. When I turned on the circuit breaker the lights all turned on, but the switch wasn't working. I then changed the switch to...
Hello,
We have three bedrooms without lights in their closets and we'd like to add a single light to each. There is an existing 20 Amp circuit that is currently only powering 4 recessed lights and a vanity light. The 4 can lights are connected to a switch in one of the bedrooms. Can I tap into...
A special: - Happy holidays for the new year 2023 to mister @marconi and to all it's UK friends who participated in my discussions and helped along the way.
I have a new 15 arm chandelier, each arm has 2 lights which use G9 LED bulbs (3W equivalent). Each arm also has four wires coming into the base of the chandelier. My question is what is the best way to wire/bundle all 60 wires so they hook up to the hot and neutral safely. There are 30 wires...
Hi I am looking for some help.
My Rangemaster cooker hood stopped working sometime ago, I’ve stripped the hood down and degreased the hood. Ive diagnosed the problem to be a faulty motor. I’ve bought a replacement motor, like for like, although the new motor has the same coloured wires but is...
Hi, I have a general question about main panel locations. The house is 120' long so I was contemplating running 2x 200amp panels located on the exterior of the house as marked in the attached photo. The main service and meter is on a pole outside. I had planned on running a trench from the main...
Hi I need advice. I am about to buy a new oven. I am moving into a new home. The original owner removed their 90cm flush range oven when they moved out.
I didn't think anything about this until PC World told me that their engineers will not install an oven unless there is a 10mm space between...
Hi,
I'm about to switch to an energy tariff whereby i think it would be better/cheaper to heat my water via my immersion heater and not my gas boiler.
I have a plain old switch attached and wanted to install a new WiFi-enabled switch or, failing that, a timer switch.
I've just opened up the...
Hi there
My old oven broke just in time for xmasðŸ˜ðŸ˜ðŸ˜ (murphys law)
Ive picked up a new one which is rated at 16amp.
The old oven came off an independent circuit. 20amp breaker with 6mm from board to isolator and 6mm to rear of oven.
Is this just a case of just hardwiring it in or is it a bigger...
Good afternoon,
Sorry for the long post but can find answers to my questions anywhere.
I’m want to replace my old cooker hood for a new one.
There is an fcu at the worktop level and T@E running behind the tiles into a round junction box above the extractor.
The old extractor is just wired...
Hi everyone
Just looking for a little advise on if my plan to run this spur is okay I’ve drawn a diagram in hopes to make my expiation simpler
The MS square is the main socket which has not been tampered with
The F is a 13 amp fuse spur
And the S are the additional sockets which I plan to...
Hello all! DIYer in Maine, USA hoping to tap into the community resources and education of professionals to help me with my home projects in a safe and responsible manner.
I've taken the supply from a neighbouring light [power source = outdoor lights] and this now controls the old and new switch as follows:
When I turn on the new lights the outdoor lights come on with a low glow
When the new lights are turned on and I turn on the outdoor lights, this turns the...
Had to replace a Light Switch with a faulty dimmer.
The New Light Switch is wired different from the old one but appears to work ok
Can someone with Aus Electrical knowledge tell me why:
- Old Light Switch was wired using Terminal 1 and 2
- Whereas New Light Switch uses only Terminal 1 and C...
I am trying to quote a job,
Small commercial kitchen/cafe/takeaway with a 3phase supply.
New 3 phase board, supplying 7 new circuits, all single phase.
1 ring with 16 double sockets.
5 radial circuits for larger appliances
1 lighting circuit
Most of it is being done in SWA
Close to 100m of...
Hi, DIYer here,
I'm replacing an old outdoor light. The old one had N, E, L and L1. The new one has N, E, L.
I guess this is a common question, how do i wire up the 4 wires coming out of my wall to the 3 available in the new light fitting please?
Attached is a pic of the old light fitting...
Hi everyone,
After much swearing and cursing (I hope the neighbours didn't hear) I've come online for some help.
We have a dimmer switch in the kitchen and my wife wanted a simple on/off switch instead. Obviously, I switched off the circuit for downstairs. Then, I unscrewed it and took a photo...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.