Hi everyone.
Someone has phoned me and asked for a CCTV system. They say their friend has one when the camera is activated through motion it will change channel on his normal TV or pops up in the corner? I've asked him to ask his friend for the make but wondered if anyone on here has any...
I wouldn't normally bother putting up any screwfix 'deals', but this one is VERY good if you fancy buying in bulk or live near a screwfix!
It looks like it's just on some 'Timco' screws, so you can either follow the link supplied below, or go to the screwfix website and type in 'timco' and then...
Hello,
i am having to install 2x 16A commando outlets in a factory that are ran from a generator outputting 127v 3 phase @ 200Hz.
Does anyone know if I can run the 200Hz wiring back into the main trunking to get to the next room (where the outlets are required) which already has normal...
Attended a 1st floor flat in a council block today and found a supply head inside a mantel cabinet where the earth was connected around the outside of a conduit housing the main supply cables before going into the cutout. Also coming out of the bottom of the cutout was another 6mm2 earth which...
Hi guys, I got called out to a jon today and the customer is wanting 19 lights fitted on his wall, these lighrs slot into the space of a brick thats been taken out, each light has a 20w lamp, 19 x 20 380W so roughly bout 1.5amps, there is already an outside socket fed from the ring, wouldit be...
nicsin02
Thread
advice
dimmer
electrical work
lights
normal
switch
Hello all, screwfux are advertising their standard 25mm SWA glands as 'IP54'. They are just normal Tower 2 part glands and I can't see any sort of rubber ring in them. Is this rating correct? A thousand thank-yous!
Will It Work ??????
Right, i have a customer who has a light fitting that has x3 watt halogen bulb light fitting run from a normal dimmer atm.
They are having wardrobes fitted that will have x3 GU10 Dimmable LED down lights on the outside :omg_smile: (Must be LED as they like the day white...
adamroche144
Thread
dimmer
dimming
fitting
halogens
led
led's
little
normal
these
Is it possible to reverse the switching on a normal 230v AC thermostat, the spec is for an extraction fan to kick in when the heat builds up. I know that I could use a relay to reverse the normally open and closed sequence but something out of the box would be better.
Thanks
Phill
Recently I had a job where I had to cut a 6mm and a 2.5mm live cable and terminate into a JB. I had to strip the cable with an insulated stanly, and then separate the wires and terminate each one.
I was just wondering if there is a tool that would do this cutting job without having to separate...
Hi,
I just done a job today and got some reading of 7ohms, on continuity of a light circuit (B6 CB) this is the highest I have yet seen
is this still ok? Or is this a problem?
Cheers
scintillasam
Thread
circuit
light
normal
point
result
start
switch
value
Have been called to a recently installed installation. Customer noticed one of the GLS BC LED lamps was glowing when turned off. Here are the facts:
Circuit tested - all tests appear normal.
Wired with feeds at the switch.
All lamps are LED
Measured voltage when lights switched on is...
matt_bei
Thread
light
light switch
lights
measured
normal
pendant
switch
switched
voltage
Hi All,
My client has asked me to replace some regular T8 flourescent 6ft tubes with new leds.
We put them in like for like but nit coming on.
When I mentioned to the wholesaler who supplied the tubes, they said I might need to recon figure the wiring in the fittings.
Can anyone shed any...
mgnelec09
Thread
electrical work
led
normal
not working
replacing
tubes
working
Hi there.
I am just wondering if this is ok to do?
I recently installed a security light and my grandmas house and I drilled straight through the kitchen wall onto the exterior front of the house to install the security pir light. I supplied the light via 2.5mm t&e as it was all I had...
reeveerx
Thread
external
going
house
light
normal
plug
right
security
socket
can anyone advise me on how you would wire up 8 downlights to be controlled by a remote control? also can the downlights be low voltage leds? any help would be appreciated
bigstu11
Thread
bathroom
controlled
dimmable
led
light
lighting
normal
remote
though
Hi Guys,
Can you help ? I just wanted to know how you wire a key switch and normal switch together. Is this how it should be :-
Feed from board to common on key switch
power to emergency lights comes off the load side of key switch
loop feed comes off the common side of key switch to common...
dave19
Thread
common
emergency
key
lights
normal
power
switch
wiring
Hi everyone, I'm making a house model in which I use one VAC bulb and another one but uses DC source. What blocking me at the moment is the electric source of the VDC bulb. I want to use circle in phone charger (I have many of them, ones of Nokia 12xx) to transform VAC into VDC and I tried but...
My dad's been with these guys since August and he's starting to complain about how bad their service is. What experience have you guys had with ATLPT? It seems very isolated, he isn't getting a whole lot of help from his tutor. Is this normal?
Hi chaps,
As some of you may recall, I posted a while back about a dodgy electrician who did some work at my parents place, including putting in a circuit for a new induction hob, as well as a board.
He cocked a load of things up so following a complaint to the NICEIC, the guy came back today...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.