overload

  1. J

    Most difficult fault

    Just wanted to know out of curiosity difficult wiring faults people have come across in there careers? what type of fault, and how you got to the bottom of it, Some faults are easier to find than other, maybe the fault was an emergency call out or perhaps something that was picked up on a EICR...
  2. C

    struggling to reset Mains after overload

    Greetings all. I have the lowest cost supply of electricity available here in France. that means that I can only have a few heaters running at the same time as the oven is on or the main rcd supplied by the electricity company trips. now my problem is trying to turn it back on again. it refuses...
  3. C

    Potential overload of ring mains

    At a house viewing I saw a dozen electric radiators connected mainly by plugs into wall sockets, one or two (in bathrooms) connected to fused spurs. I calculated nearly 14Kw and I'm given to understand all these rads are connected to either of two ring mains with 32A breakers. A quick look at...
  4. T

    Overload protection omission

    Hi folks, not posted in a while but I have been having a few interesting discussions about this one !!! I have come across a cooker connection outlet which is wired in 6mm and supplied via 45a dp sw and a 32a MCB Now in this outlet I have an oven at 3kw wired in 2.5mm HOFR and a sparker for...
  5. HoverSPRX

    No Overload Protection on DB wired to Busbar

    Hi all, I recently carried out an EICR on a biolabs, it has a DB in the mains room that was wired direct into the busbar on 25mm tails within 3M. The busbar is on a 200A fuse and the DB in question is a 24 way three phase board. I know that 20 + years ago when this was installed some guy has...
  6. O

    Overload Protection - Major Renovation

    Hi All, First post on this forum, but I've been reading the great questions and answers for years, so I hope someone can help me out? I've renovated a few houses in my time and done some of the basic wiring myself, but my latest 1940's house is a real project and needs a professional's...
  7. P

    thermal constraints

    what 2 methods are they to determine the sustainability of a protective conductor for thermal constraints during earth fault conditions?? And might be a long shot but can anyone tell me what component of a RCD will operate for a .. a. line to earth fault 2.3 ohms b. line to neutral fault 0.01...
  8. A

    Beko Condenser not heating

    hi, I have a Beko DC7110 condenser dryer that's not heating, I have cleaned out all filters etc, the heating element has been replaced(which includes thermal overload) and the front thermal overload has been resistance tested and is fine, what could potentially be the reason? Thanks
  9. Pat H

    Cable size less than protective device rating

    Noted today an interesting comment on page 43 of christopher kitchers Practical guide to inspection, testing and certification of Electrical Installations ( a great book ) Under Shower curcuits he states: For this type of circuit it is possible to have a cable which has a current rating of less...
  10. B

    Overload or what ?

    I got a call from a lad who runs a snack shop asking why his fuse kept 32 amp fuse kept tripping . I went to the shop to have a look he has a total of 20000 watts (100 amps )on at one time with fryers, hot plates ,grills etc ! All single phase . Having little experience myself as a spark I...
  11. dlt27

    No overload protection.

    Just a quick question. What code for no overload protection. I know any live part to touch is code 1. Somebody as put rccb on shower and it hasn't got no overload protection apart from bullet fuse. Also fusewire bypassed. This is a landlords flat! I want to put code 1, but it only becomes...
  12. C

    Contactor overload

    Hi all, had a blocked pump that caused a overload on motor, ocpd went before motor overload. Should the motor overload always discriminate with ocpd and operate first? The motor overload was set to auto but I don't think it ever operated under fault. Motor draws 6amps under load and the motor...
  13. B

    Setting the overload on a motor circuit contactor.

    Hi I haven't much experience on this subject so thought id ask!. I need to choose and set the overload on a circuit contactor containing an overload. It's a 3ph motor rated at 14.1 amp do i set the overload at the same current rating or just above due to the initial inrush?
  14. Davehaywire

    3 pole dol starter with overload for a sp motor

    Hi Looking for a wiring diagram for the above anyone have one? Cheers
  15. S

    Overload relay in series with contactor latching circuit- Why?

    Recently had to work on Chinese plastics dryer with an overload relay wired in series with contactor latching circuit auxiliary contacts. When the overload trips you can still turn on the motor while the button is pressed. Why is that? It should be tight before the A1 or A2 terminal I have seen...
  16. J

    fused spur wiring... advice

    i was at work today replacing some sockets and backboxes and there was 2 fused spurs im a 1st year apprentice... i dropped the faceplates put the new backboxes in etc... and there was a linking cable for the 2 fused spurs and i linked the supply and the actual linking cable together in the...
  17. F

    Overload

    Question an under floor heating/ cooling box reading 17amp on my clamp meter but the supply is from a 13amp plug now I no a fuse or mcb can take 1 1/2 times its load for a certain time not sure for how long but my question is why hasn't this took the 13amp fuse out
  18. O

    Waterfall & Motor Overload!!

    As part of a large waterfall installation I'm installing a single phase 0.75kW motor with time clock and need advice on the overload setting please! I was told anything above 0.5hp/0.37kW required a contactor with thermal overload?! I'm aware the 3 phase calculation would be... kW/ Vl x sqrt 3...
  19. ebow72

    Am2 2015

    Hello folks, not posted in a while, been busy. However this week I have been slightly busier than usual. I completed my AM2, results due tomorrow morning 8 AM... I did the PRE AM2, I did find it a big help. Glad I did it. AM2 consisted of the following - Risk Assessment, Safe Isolation. There...
  20. edexlab

    Overload tripping

    At work there has been a problem I've been told about, small 1.8 Kw 3 phase fans tripping the overloads I'm not really involved in this but I am interested...... The fans are run off Inverters and the OL's for any circuit are usually within the control panels, length of run is upto 35 metres...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
This website was designed, optimised and is hosted by Untold Media. Operating under the name Untold Media since 2001.
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock