Hi everyone, first time on the forum!
I am a graduate student in chemical oceanography examining the degradation products of different plastic polymers in seawater during photo-oxidative degradation. As part of my experimental design I am using a 4.0A, 460W UV lamp to accelerate degradation of...
Hi all, about to do a condition report on a grade 2 listed 4 bedroom property, the owner is moving and wants to rent it out. The consumer unit is a PLASTIC split board RCD sited in a cupboard under the only set of stairs .The board and installation is neatly installed (even the bonding cables...
Hi all, hoping everyone has enjoyed their bank holiday weekend. I hope this post goes in the right place as I've just joined. I'm looking to swap a two way light switch and two double plug sockets from bog standard plastic ones to stainless steel ones, the existing wiring (old colours) has an...
Hi.
I am planing on building a (not sure what to call it) U shaped storage solution which goes either side and above the headboard of a bed. I want to install a couple of reading lights either side.
A mixture of me not being bothered and running out of money means I cant run cable on the...
Hi,
I have just organised an EICR for our house through a national chain of letting agents (we were short of time). The report came back with a C2 for a plastic consumer unit. It is next to the front door (not in a cupboard) and it is not at the only point of exit and was installed in 2012 with...
Hi guys, sorry if this has been asked before.
I’m currently in a flat where the tenant queried the water bonding. There’s a 6mm green and yellow leaving the DB and goes to the gas meter as it’s clipped direct I can see it isn’t continuos and go to the water. There is also no other bonding...
Good old amendment 3 and the demise of all that's plastic, we have seen many discussions on the good old plastic consumer units, so now for those EICR's where plastic has and will be around for quite some time, SO !!
We all seem to have slightly differing views on this, but here goes.
C2 if...
Hi I need some impartial advice about my plastic consumer unit. It is mounted on the wall above some stairs in my flat. I have been told it doesn't meet building regs and must be replaced with a metal one. Would this area count as an escape route? Do I have to change the unit?
Many many thanks...
Hi sorry very long one. Please hop to bottom paragraph for short version. I’m just about to refurb bathroom in my 1986 house but bonding always confused me and I am still confused now! So my main incoming water pipe (extraneous) is Currently bonded To MET in 10mm and hot and cold pipes cross...
Being a bit naughty, as this isn't electrical, but I thought It would get far more replies rather than in another part of the forum. Reckon I've got an hour or two before Westward spots it ?.
I need to get some weight plates for my barbell, standard 1" diameter hole (not olympic size). However...
Hi all
Apologies if it is a stupid question and have been discussed here before.
Generally I always hire a professional but since in current situation I need to replace of the switch in one of rooms. Situation is:
Current Scenario:
Plastic back box
Metal switch
Earth wire terminates in the...
where can I get the control end panel " the plastic part "complete with controls etc for a rointe K serie ,it has 11 panels .I am in Dublin .
It is not working correctly ,display goes white
Thank you ,
Niall O Connor .
Hi
Looking for some advice please.
I started renovating my house in 2015 and as part of this I ripped out all the wiring and got my electrician to rewire it including a new plastic consumer unit. There is still some electrical work to do so none of it had been signed off yet.
As the plastic...
Hello All
Noticed the existing bonding for the cold water supply is only 4mm. The supply pipe out of the ground is clearly a plastic pipe. It joins a brass stopcock under the kitchen sink cabinet and the rest of the plumbing in the house is in copper. I'm worried I need 10mm bonding and will...
So this has been asked a few times but still not 100% clear on this
I have to add a cable to a an existing 17th ed board , all the existing cabling is rear entry but this isn’t possible for my new cable. So Im going to cut a 20mm hole in the bottom and use a 20mm plastic stuffing gland to run...
I’ve just had a new stud wall put up. I have chrome light switches throughout the house but with metal pattress boxes. Am I correct in thinking a plastic drywall pattress box will be ok with a metal switch as long as the CPC is wired into the faceplate....or do I put in another noggin and use...
So, I have a customer who wants the dodgy wiring in his cellar extending - currently he has a lighting circuit clipped with plastic clips, down to a bulkhead light and a double 13A socket for his freezer....
So I'm quoting him to run off a ring main to the socket, and install another socket and...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.