On the coming job i have to do a new wiring on massive shop.Deal its between me and show owned.There its about 200 m2 place with shelf's where shoes and handbag have to display.+ reception + office + 3 toilets + shower .I don't have any problem to to this job but im not clear on the RCD...
Hi, I'm basically installing a single weatherproof socket in a garden for a pond pump, and I'm wondering if there are any sockets with a stake attached, to knock it in the ground, in situations where there is no permanent fixing point? Just wondering what people have done in this scenario and...
Hi, carried out an inspection this week on an installation which consisted of two phase three wire to a small building from an electrical switch room. The supply is wired using 25mm LSF/SWA protected by BS-88 at the sub. At the building the supply is terminated into a 947-3 isolator and then...
Paultrim123321
Thread
building
distribution
fault
protected
protection
question
supply
tails
I might be COMPLETELY wrong.... but I have recently finished my level 3 in college and I'm sure I was told that if a Zs value is higher than the max reading in BS7671 it's okay if it's protected by a 30mA RCD, so it passes. I sort of remember writing 'satisfactory' on the test form next to Zs...
:confused5: I have been asked to wire up a couple of CU on plug tops on a display for tenants to show how to go about basic fault finding before they send for a call out .
I used 2 wylex boards , one with dual rcd and one with none .
I put a neutral earth fault but that resulted in the plug...
Hi Guys, Customer has brought a Lay-Z- Spa pool (basically an inflatable hot -tub) which comes with pre-wired plug top and flex for the pump/heater controls etc. The pool will be positioned outside, rear of detached garage. I proposed wiring an outside weather proof skt which will be RCD...
Right here's the info...there's a small 2-way consumer unit in a external garage. Just a 40A main switch with two MCB's one for lights & one for sockets. Was adding lights & sockets today & the guy I work with said that as we were adding to the circuits we'd have to replace the main switch with...
Hey guys!
I have recently been ask to install a submain to a customers workshop.
The installation I was going to use was a 100mA DP Timedelay RCD with a 32A MCB at the supply origin for the SWA submain. In the workshop I was wondering if I can install and DP Isolator with RCBOs to protect the...
Hi I have a 6 way split load board located in the shed and served by 10mm SWA. Anything on the unprotected side of the board tests and works fine. However this is not the same for the protected side. I can plug a radio in and the circuit does not trip, but if I use the lawn mower or a drill the...
Templer
Thread
button
doesnt
neutrals
protected
rcd
test
trip
trips
I've been asked to do some minor alterations to an out house which is supplied from CU in main house. Now the new CU in outhouse has RCD protected circuits but the supply from main house is not RCD protected. The cable is a 20m run in hightuf clipped to outside wall clearly visible. Should I put...
HI SPARKYS
JUST A QUICK BIT OF ADVICE REQUIRED.
HAVE RECENTLY BEEN TO PRICE A DB CHANGE OF THE DUAL SPLIT LOAD VARIETY.and noticed the instal has a dedicated smoke detection circuit .Now i have also noticed that this circuit is buried in plaster (through a safe zone) and in fact all circuits...
I'm installing a gate supply at the end of a customers garden. My plan is to spur off internal ring main and run a radial roughly 100m to end of garden. Providing the long run cable is of adequate size to sustain 230v to the end of the garden am I right in thinking that I can tee off again at...
Hi,
I am an industrial electrician and have been asked by a friend to do some work on their house. I would like some advice on RCD's.
I have been asked to install a light and a socket in a garden shed. I am planning to supply the shed via the garage which already has a supply from a 32a...
Hi i recently went to a job for a partial rewire, it's a 16th ed board, 3 circuits RCD protected 6 not RCD protected. They want to keep the existing board. I will replace some of the MCBs on the unprotected side with RCBOs for the new circuits, would this be compliant? Even though some existing...
Got called to a house the other day RCD trips when switcing on the kitchen light only problem is that they have a split board with one RCD that protects sockets, shower and cooker. The lights up and down and smokealarm are not protected by any RCD
I changed the light switch and it has improved...
haden
Thread
circuit
circuits
fault
interesting
light
problem
protected
rcd
went to an office this week where there are 2 rcbo's nuisance tripping every now and then. apparently one does the floor sockets in the office and one does the wall sockets in the office, now as the office was full of staff working on their computers i could only go by what one member of staff...
got a split board in a house, going to put a sub board in the attic to supply sockets and lights, do i need an rcd on the sub board.? the main cable going to the attic will be 10mm on a 50A mcb with rcd main switch.
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.