receiver

  1. happysteve

    Quinetic wireless switches and receiver

    Eh up :) Installed a set of "Quinetic" kinetic wireless switches and receiver today, in a situation where the landing light L was fed from the downstairs lighting circuit, and the N return on the upstairs lighting circuit. (Very wrong, and all too familiar). For those unaware, the switches...
  2. G

    Help wiring receiver

    Hi, I have recently purchased a hive heating control. I currently have a Potterton boiler with a integrated 24h timer. The only other control over the heating is a thermostat in the hall. I need to disconnect the thermostat and connect the Hive receiver. Any help is much appreciated. Please see...
  3. S

    How do I Wire Main combi Eco 25 and HIVE 2 single channel receiver.

    Hello I have a Main combi Eco 25 (without timer) I would like some advice to connect it to my HIVE single channel receiver. I have included I photo of the boilers wiring diagram. My hive receiver is single channel and has these conections. N L 1 Common 2 Heating off 3 Heating on 4 (unused)...
  4. R

    Remote control ceiling fan stopped working

    Hello, I have a remote control ceiling light fan which has stopped working via the remote control. The light still comes on and off when using the main wall switch but that is it. The remote used to control the light and the fan movement but now nothing. I did the obvious and replace the...
  5. Dan

    What's Your Speaker / Amp Setup?

    I have an Onkyo SR606 with 4 bookshelf speakers (no bass or centre). Just seen this though...
  6. G

    Boss RF receiver portable thermostat heating controls

    Hi I had to get a new unit, my old one was a Honeywell where there was a flex from the boiler with 5 wires , three to one terminal and two to another. These are marked grey wire N brown wire L and brown L and other terminal is A brown B Grey and C no wire. The instructions are rubbish and I...
  7. Hellmooth

    Remote controlled lighting

    Customer is looking to control some lighting from a remote/button, has anyone fitted anything similar, it's only for 1 circuit. I've installed universal receivers that can control garage doors and gates, I have used these to switch a contactor to control outside lights, was hoping for something...
  8. C

    Siding gate radio receiver

    Hi guys can anyone help me ID the radio receiver in the picture.:smile5: PS how do I upload a photo :frown:
  9. N

    Hot water thermostat problem

    We have what I'm guessing would be considered a 3 zone heating system: Zone 1 - downstairs radiators Zone 2 - upstairs radiators Zone 3 - hot water cylinder We have programmable wireless thermostats for zones 1 and 2 (1 each), a timer for the hot water and also a wireless thermostat for the hot...
  10. chudson

    Wireless switching solution

    I have a problem that needs solving - there should be a product for it on the market but I can't find it! Problem: 2 lights are run from an interior switch, my client would like the gate relay to turn these lights on also as well as having the switch override on - not off. Would be simple with...
  11. H

    Replacing Potterton EP 2002 programmer / Satchwell room thermostat with RF receiver

    Hi, In a property that is being renovated there is a Potterton Profile 100e boiler controlled by a Potterton EP2002 Controller wired to an ancient Satchwell room Thermostat. Is it possible to replace this controller / room stat combination with a modern RF room thermostat linked to an RF...
  12. D

    wirelss switch

    hello trying to source a wireless switch just to switch a standard light with a 1 gang 1 way at the moment there is a switch operating light but its the other end of the room as the room was altered but didnt bother to relocate the switch. so now its all painted and decorated and customer...
  13. J

    Wireless PIR

    Hi, I am changing some communal stair lighting in a block of offices and they want them to be on PIR sensors. Does anyone know of a product that uses just a master PIR that you wire into the switch line for all the lights, and then a wireless sensor i can fit at each level that will active the...
  14. applemac

    mk wireless switching

    im pricing a posh extension and customer has requested mk wireless switches as the walls are exposed stonework, are these any good and anyone fitted them before ? im feeding 16 gu10 leds split into two circuits and 6 small led wall spot lamps...
  15. S

    Is it possible to use a single phase ballast on a two phase service receiver?

    Hi guys! My pleasure to be amongst you fine folk in the UK! Sorry for the long read, but I am wanting to know if there is a way I can split my single phase ballast into feeding a neon bulb on my vehicle with two phase function. I have a 1998 Lincoln Mark VIII which has a "neon beam" running...
  16. M

    heating controls

    iv got contactors,timers and stats to fit to panel heater circuits today and tomorrow BUT unknown to guy who surveyed( had a look and counterd heaters) there is a system inplace already its dimplex panelheaters with controler modules which are removable and a wall mounted timer stat which...
  17. J

    Wireless room stat and mains controls

    Hi everyone I am wondering if I can control a mains 3 port valve with a wireless room stat. The plumbers didnt advise me on this stat until the job was finished I have had this problem before. Can anyone help. Thanks
  18. T

    Help wiring Honeywell CMT927 roomstat into Combi boiler

    Hi all, Could somebody please help me understand the following diagrams on wiring my new room stat into my boiler. Boiler - Vaillant Turbomax Pro 24e Stat - Honeywell CMT927 Wireless Boiler wiring: Page 17 of the following PDF link...
  19. S

    Wireless thermostats

    Hi I'm not familiar with central heating controls at all, but yesterday I was helping another customer in my local wholesalers and none of their digital thermostats in the catalogue where hard wired controls, they where all wireless and the only wired controls where the ones with the...
  20. S

    Wireless Thermostat

    Got a new one today, and the boiler ain't firing up now. Got power at the receiver as the light is one but doesn't seem to anything going out, even when I press the manual over-ride. Not got a multimeter on me so can't check for voltage going out. Maybe faulty receiver. Anything else it could be?

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
This website was designed, optimised and is hosted by Untold Media. Operating under the name Untold Media since 2001.
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock