good evening all,
If I have an existing 10mm T+E from the CU to the rear of the house external ending in a junction box on the wall already in place (total length 9M) and I want to connect this to an armoured cable 2 core + CPC from the exterior junction box to a rear garden new future sauna...
What is everyone's thoughts on double pole rcbo's vs single pole, I mostly use Fuse Box these days with the odd Hager board if i'm feeling flush. I usually use the single pole fuse size rcbos. recently I tried the mini double pole rcbos but for the extra cost I think I will go back to using...
I recently switched from economy 7 to a single rate smart meter. I have two fuse boards and wondered should these now be on 24hours a day and should they be charged at the same rate?
I got my bill through and it looks like they are charging us at different rates, both of which are higher than...
Looking for some advice;
I am intending to mount two led downlights on pillars/brick walls either side of the garage door opening. I will drill through the cavity to feed the cable through. There will be a PIR sensor mounted in the middle above the garage door.
Internally i wanted to put the...
Am replacing a faulty dimmer. Have put live in C, the blue in L1 and earthed green - doesnt work. It looks like my old dimmer had live and blue in L1 and L2 but I should have taken a picture. Is that even possible? I can try that of course or is it more likely that the connection wire isnt in...
Hi,
Hope someone could help with below situation or recommend a good forum to ask about or find information on as I read a lot on the forums and watched many videos but it just got very confusing.
Objective
We acquired 7 sets of led sugar canes, each set has 40 Red leds and is powered by 2 AA...
Do RGB LED chips with single beads for each colour exist higher powered than 3W, and if so could anyone recommend one? I've been trying out these (which seem to be comparable to these) - is it possible to find higher powered variations?
i know that it is possible to find 10W chips but these...
Looking for some advice and insight on best practices here. I have an attached garage 25 feet away from my main 200amp service panel in my home.
I want to use a mig welder, a 3HP table saw, and a 2HP belt grinder in my garage.
I have plenty of room in my panel to add a circuit for each, but to...
We have got a hydraulic motor/powerpack for leveling legs of a trailer. However this trailer is running off a 15KW inverter, so the motor needs to run off single phase.
The motor has come configured for 3 phase, however the motor plate does say it will run off single phase.
Would i be right in...
HI Guys,
I bought this motor and speed controller used and tried wiring as per the diagram on the side of the speed control unit but the motor will not turn on. I am running it at 220v, when plugged in I do see the green led light up. There is not much info on the internet. But I was able to...
Hello! I have a high-pressure compressor equipped with a single phase motor! The motor have 2 capacitors, 1 continuous and 1 for starting, with a relay for isolation . The motor is old, but it's still working! I have changed the capacitors with new ones and the cable too. The motor work ok! I...
New to the forum and first-time poster!
Currently trying to confirm what the top meter (circled) in the photos supplies? To me, it seems the meter tails enter the connector block and then there are two outputs coming from the block - one to the top isolation switch and one to the lower...
Hi everyone
There is a switch board which is single phase, but when you look at the back you will see 2, 16mm cable go to the fuse(red and white). What is that for ? I haven't seen before.
And the black and blue cable goes to the service neutral link !!!
In Australia 3 phase color is Red White...
Got called to "a flat in Manchester has no hot water" at 16:30 today and to be frank I was a little miffed to have to attend.
So arrives at site, spends 20mins finding parking, 30 mins finding the site contact, getting keys and then being informed that it was not one flat but eleven.
Have no...
Hi I’m upgrading the fog lamps on a 2013 Range Rover sport to combined FOG and DRL got the fogs working but have a single wire to be connected to an ignition live, where will the closest ignition live wire be
Hi, I have been asked to fit a 32a isolator ready for an air con unit and picked one up from screwfix. Unfortunately the one I have is a 4 pole, can this still be used with 6mm t&e or do I need to replace it with a 2 pole. If it can be used do I just use terminals L1 & T2
Thanks
Got an emergency call out from a very worried old lady the other night - the power at her apartment had gone off and the kitchen light was smouldering badly. She'd been on the phone to the DNO (Northern Powergrid), they were telling her to turn the main switch off but she couldn't understand and...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.